Отвалился Logitech mk295 combo после обновления на 10.7

Автор Tatarinovolg, 13 декабря 2020, 10:58:06

« назад - далее »

0 Пользователи и 1 гость просматривают эту тему.

Tatarinovolg

Моё почтение уважаемому форуму.
После обновления ядра до версии 4.19.0-13
amd64 отвалились мышь и клавиатура. В режиме загрузчика grub и bios все работает. Если загрузится с ядром 4.19.0-12 тоже все работает.
Поставил ядро 5.9 из бэкпорта - не работает.
При загрузке из liveCD debian 10.7 xfce - не работает.
В Линукс я новичок. Реально ли решить проблему?

qupl

Беспроводные? Логи, информация об оборудовании и ОС?

Tatarinovolg

#2
С ядром 4.19.0-12-amd64

lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 046d:c534 Logitech, Inc. Unifying Receiver
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


lspci
00:00.0 Host bridge: ULi Electronics Inc. M1697 HTT Host Bridge
00:01.0 PCI bridge: ULi Electronics Inc. PCI Express Root Port
00:02.0 PCI bridge: ULi Electronics Inc. PCI Express Root Port
00:03.0 PCI bridge: ULi Electronics Inc. PCI Express Root Port
00:04.0 PCI bridge: ULi Electronics Inc. PCI Express Root Port
00:11.0 PCI bridge: ULi Electronics Inc. M5249 HTT to PCI Bridge
00:12.0 Ethernet controller: ULi Electronics Inc. ULi 1689,1573 integrated ethernet. (rev 60)
00:13.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
00:13.1 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
00:13.2 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
00:13.3 USB controller: ULi Electronics Inc. USB 2.0 Controller (rev 01)
00:14.0 Audio device: ULi Electronics Inc. HD Audio Controller (rev 01)
00:15.0 ISA bridge: ULi Electronics Inc. PCI to LPC Controller (rev 10)
00:15.1 Bridge: ULi Electronics Inc. M7101 Power Management Controller [PMU]
00:16.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c7)
00:16.1 IDE interface: ULi Electronics Inc. ULi M5288 SATA
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: NVIDIA Corporation NV43 [GeForce 6600] (rev a2)



dmesg
[    0.000000] Linux version 4.19.0-12-amd64 (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.152-1 (2020-10-18)
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.19.0-12-amd64 root=UUID=d3db0ad5-93d6-4744-955d-7f9a4488be47 ro quiet
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c7fcffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000c7fd0000-0x00000000c7fddfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000c7fde000-0x00000000c7ffffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000ff780000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000137ffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.3 present.
[    0.000000] DMI: MSI MS-7270/MS-7270, BIOS V1.9 04/11/2008
[    0.000000] tsc: Fast TSC calibration failed
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] last_pfn = 0x138000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0000000000 mask FF80000000 write-back
[    0.000000]   1 base 0080000000 mask FFC0000000 write-back
[    0.000000]   2 base 00C0000000 mask FFF8000000 write-back
[    0.000000]   3 base 0100000000 mask FFE0000000 write-back
[    0.000000]   4 base 0120000000 mask FFF0000000 write-back
[    0.000000]   5 base 0130000000 mask FFF8000000 write-back
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000138000000 aka 4992M
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT 
[    0.000000] e820: update [mem 0xc8000000-0xffffffff] usable ==> reserved
[    0.000000] last_pfn = 0xc7fd0 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f]
[    0.000000] RAMDISK: [mem 0x33b07000-0x35d7afff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F8AD0 000014 (v00 ACPIAM)
[    0.000000] ACPI: RSDT 0x00000000C7FD0000 000038 (v01 A M I  OEMRSDT  04000811 MSFT 00000097)
[    0.000000] ACPI: FACP 0x00000000C7FD0200 000084 (v02 A M I  OEMFACP  04000811 MSFT 00000097)
[    0.000000] ACPI: DSDT 0x00000000C7FD0440 0047F2 (v01 1ADIJ  1ADIJ000 00000000 INTL 02002026)
[    0.000000] ACPI: FACS 0x00000000C7FDE000 000040
[    0.000000] ACPI: APIC 0x00000000C7FD0390 000068 (v01 A M I  OEMAPIC  04000811 MSFT 00000097)
[    0.000000] ACPI: MCFG 0x00000000C7FD0400 00003C (v01 A M I  OEMMCFG  04000811 MSFT 00000097)
[    0.000000] ACPI: SSDT 0x00000000C7FD4C40 00002B (v01 OEM_ID OEMTBLID 00000001 INTL 02002026)
[    0.000000] ACPI: OEMB 0x00000000C7FDE040 000056 (v01 A M I  AMI_OEM  04000811 MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x0000000137ffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x137ff7000-0x137ffbfff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x0000000137ffffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000c7fcffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x0000000137ffffff]
[    0.000000] Zeroed struct page in unavailable ranges: 146 pages
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000137ffffff]
[    0.000000] On node 0 totalpages: 1048430
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 12736 pages used for memmap
[    0.000000]   DMA32 zone: 815056 pages, LIFO batch:63
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 229376 pages, LIFO batch:63
[    0.000000] Detected use of extended apic ids on hypertransport bus
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[    0.000000] IOAPIC[1]: apic_id 2, version 17, address 0xfec10000, GSI 24-44
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] smpboot: Allowing 2 CPUs, 1 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xc7fd0000-0xc7fddfff]
[    0.000000] PM: Registered nosave memory: [mem 0xc7fde000-0xc7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xc8000000-0xff77ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff780000-0xffffffff]
[    0.000000] [mem 0xc8000000-0xff77ffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] random: get_random_bytes called from start_kernel+0x93/0x52a with crng_init=0
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] percpu: Embedded 45 pages/cpu s144408 r8192 d31720 u1048576
[    0.000000] pcpu-alloc: s144408 r8192 d31720 u1048576 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1032025
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.19.0-12-amd64 root=UUID=d3db0ad5-93d6-4744-955d-7f9a4488be47 ro quiet
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] AGP: Node 0: aperture [bus addr 0x8540000000-0x8541ffffff] (32MB)
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] AGP: Your BIOS doesn't leave an aperture memory hole
[    0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[    0.000000] AGP: This costs you 64MB of RAM
[    0.000000] AGP: Mapping aperture over RAM [mem 0xbc000000-0xbfffffff] (65536KB)
[    0.000000] PM: Registered nosave memory: [mem 0xbc000000-0xbfffffff]
[    0.000000] Memory: 3936168K/4193720K available (10252K kernel code, 1247K rwdata, 3312K rodata, 1596K init, 2264K bss, 257552K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] ftrace: allocating 31917 entries in 125 pages
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 33024, nr_irqs: 512, preallocated irqs: 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] ACPI: Core revision 20180810
[    0.000000] APIC: Switch to symmetric I/O mode setup
[    0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.024000] tsc: PIT calibration matches PMTIMER. 1 loops
[    0.024000] tsc: Detected 2010.051 MHz processor
[    0.000013] tsc: Marking TSC unstable due to TSCs unsynchronized
[    0.000027] Calibrating delay loop (skipped), value calculated using timer frequency.. 4020.10 BogoMIPS (lpj=8040204)
[    0.000031] pid_max: default: 32768 minimum: 301
[    0.000087] Security Framework initialized
[    0.000089] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.000119] AppArmor: AppArmor initialized
[    0.004502] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.005553] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.005615] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.005659] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.006010] LVT offset 0 assigned for vector 0xf9
[    0.006013] process: using AMD E400 aware idle routine
[    0.006015] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
[    0.006016] Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4, 1GB 0
[    0.006018] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.006020] Spectre V2 : Spectre mitigation: LFENCE not serializing, switching to generic retpoline
[    0.006076] Spectre V2 : Mitigation: Full generic retpoline
[    0.006077] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.125475] smpboot: CPU0: AMD Athlon(tm) 64 Processor 3200+ (family: 0xf, model: 0x4f, stepping: 0x2)
[    0.125680] Performance Events: AMD PMU driver.
[    0.125685] ... version:                0
[    0.125687] ... bit width:              48
[    0.125687] ... generic registers:      4
[    0.125688] ... value mask:             0000ffffffffffff
[    0.125689] ... max period:             00007fffffffffff
[    0.125690] ... fixed-purpose events:   0
[    0.125690] ... event mask:             000000000000000f
[    0.125765] rcu: Hierarchical SRCU implementation.
[    0.126304] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.126373] smp: Bringing up secondary CPUs ...
[    0.126374] smp: Brought up 1 node, 1 CPU
[    0.126375] smpboot: Max logical packages: 2
[    0.126378] smpboot: Total of 1 processors activated (4020.10 BogoMIPS)
[    0.127079] devtmpfs: initialized
[    0.127167] x86/mm: Memory block size: 128MB
[    0.127975] PM: Registering ACPI NVS region [mem 0xc7fde000-0xc7ffffff] (139264 bytes)
[    0.128014] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.128014] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.128014] pinctrl core: initialized pinctrl subsystem
[    0.128014] NET: Registered protocol family 16
[    0.128014] audit: initializing netlink subsys (disabled)
[    0.128014] cpuidle: using governor ladder
[    0.128014] cpuidle: using governor menu
[    0.128014] node 0 link 0: io port [1000, ffffff]
[    0.128014] TOM: 00000000c8000000 aka 3200M
[    0.128014] node 0 link 0: mmio [a0000, bffff]
[    0.128014] node 0 link 0: mmio [c8000000, ffffffff]
[    0.128014] TOM2: 0000000138000000 aka 4992M
[    0.128014] bus: [bus 00-ff] on node 0 link 0
[    0.128014] bus: 00 [io  0x0000-0xffff]
[    0.128014] bus: 00 [mem 0x000a0000-0x000bffff]
[    0.128014] bus: 00 [mem 0xc8000000-0xffffffff]
[    0.128014] bus: 00 [mem 0x138000000-0xfcffffffff]
[    0.128014] ACPI: bus type PCI registered
[    0.128014] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.128014] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.128014] PCI: not using MMCONFIG
[    0.128014] PCI: Using configuration type 1 for base access
[    0.128649] audit: type=2000 audit(1607855532.148:1): state=initialized audit_enabled=0 res=1
[    0.128808] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.129183] ACPI: Added _OSI(Module Device)
[    0.129184] ACPI: Added _OSI(Processor Device)
[    0.129185] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.129186] ACPI: Added _OSI(Processor Aggregator Device)
[    0.129187] ACPI: Added _OSI(Linux-Dell-Video)
[    0.129188] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.132081] ACPI: 2 ACPI AML tables successfully acquired and loaded
[    0.133518] ACPI: Interpreter enabled
[    0.133541] ACPI: (supports S0 S1 S4 S5)
[    0.133542] ACPI: Using IOAPIC for interrupt routing
[    0.133964] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.135216] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.135243] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.135568] ACPI: Enabled 3 GPEs in block 00 to 3F
[    0.135578] ACPI: Enabled 4 GPEs in block 40 to 5F
[    0.144305] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.144313] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.144318] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.144603] PCI host bridge to bus 0000:00
[    0.144607] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.144608] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.144610] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.144612] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window]
[    0.144614] pci_bus 0000:00: root bus resource [mem 0xc8000000-0xffffffff window]
[    0.144616] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.144627] pci 0000:00:00.0: [10b9:1697] type 00 class 0x060000
[    0.144771] pci 0000:00:01.0: [10b9:524b] type 01 class 0x060400
[    0.144793] pci 0000:00:01.0: enabling Extended Tags
[    0.144822] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.144934] pci 0000:00:02.0: [10b9:524c] type 01 class 0x060400
[    0.144952] pci 0000:00:02.0: enabling Extended Tags
[    0.144979] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.145086] pci 0000:00:03.0: [10b9:524d] type 01 class 0x060400
[    0.145104] pci 0000:00:03.0: enabling Extended Tags
[    0.145131] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[    0.145237] pci 0000:00:04.0: [10b9:524e] type 01 class 0x060400
[    0.145255] pci 0000:00:04.0: enabling Extended Tags
[    0.145281] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[    0.145400] pci 0000:00:11.0: [10b9:5249] type 01 class 0x060400
[    0.145513] pci 0000:00:12.0: [10b9:5263] type 00 class 0x020000
[    0.145527] pci 0000:00:12.0: reg 0x10: [io  0xe800-0xe8ff]
[    0.145534] pci 0000:00:12.0: reg 0x14: [mem 0xd7fefc00-0xd7fefcff]
[    0.145578] pci 0000:00:12.0: PME# supported from D3hot D3cold
[    0.145670] pci 0000:00:13.0: [10b9:5237] type 00 class 0x0c0310
[    0.145683] pci 0000:00:13.0: reg 0x10: [mem 0xd7fee000-0xd7feefff]
[    0.145808] pci 0000:00:13.1: [10b9:5237] type 00 class 0x0c0310
[    0.145820] pci 0000:00:13.1: reg 0x10: [mem 0xd7fed000-0xd7fedfff]
[    0.145953] pci 0000:00:13.2: [10b9:5237] type 00 class 0x0c0310
[    0.145965] pci 0000:00:13.2: reg 0x10: [mem 0xd7fec000-0xd7fecfff]
[    0.146096] pci 0000:00:13.3: [10b9:5239] type 00 class 0x0c0320
[    0.146111] pci 0000:00:13.3: reg 0x10: [mem 0xd7fef800-0xd7fef8ff]
[    0.146163] pci 0000:00:13.3: PME# supported from D0 D3hot D3cold
[    0.146268] pci 0000:00:14.0: [10b9:5461] type 00 class 0x040300
[    0.146284] pci 0000:00:14.0: reg 0x10: [mem 0xd7fd4000-0xd7fd7fff 64bit]
[    0.146329] pci 0000:00:14.0: PME# supported from D0 D3hot D3cold
[    0.146424] pci 0000:00:15.0: [10b9:1573] type 00 class 0x060100
[    0.146575] pci 0000:00:15.1: [10b9:7101] type 00 class 0x068000
[    0.146626] pci 0000:00:15.1: quirk: [io  0x4000-0x403f] claimed by ali7101 ACPI
[    0.146730] pci 0000:00:16.0: [10b9:5229] type 00 class 0x01018a
[    0.146763] pci 0000:00:16.0: reg 0x20: [io  0xff00-0xff0f]
[    0.146776] pci 0000:00:16.0: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.146778] pci 0000:00:16.0: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.146780] pci 0000:00:16.0: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.146781] pci 0000:00:16.0: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.146885] pci 0000:00:16.1: [10b9:5288] type 00 class 0x010185
[    0.146899] pci 0000:00:16.1: reg 0x10: [io  0xe400-0xe407]
[    0.146905] pci 0000:00:16.1: reg 0x14: [io  0xe000-0xe003]
[    0.146912] pci 0000:00:16.1: reg 0x18: [io  0xd800-0xd807]
[    0.146918] pci 0000:00:16.1: reg 0x1c: [io  0xd400-0xd403]
[    0.146924] pci 0000:00:16.1: reg 0x20: [io  0xd000-0xd00f]
[    0.146931] pci 0000:00:16.1: reg 0x24: [mem 0xd7fef400-0xd7fef7ff]
[    0.146957] pci 0000:00:16.1: PME# supported from D3hot
[    0.147058] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
[    0.147149] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
[    0.147239] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
[    0.147327] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
[    0.147479] pci 0000:01:00.0: [10de:0141] type 00 class 0x030000
[    0.147494] pci 0000:01:00.0: reg 0x10: [mem 0xd8000000-0xdbffffff]
[    0.147504] pci 0000:01:00.0: reg 0x14: [mem 0xc8000000-0xcfffffff 64bit pref]
[    0.147513] pci 0000:01:00.0: reg 0x1c: [mem 0xde000000-0xdeffffff 64bit]
[    0.147525] pci 0000:01:00.0: reg 0x30: [mem 0xddfe0000-0xddffffff pref]
[    0.147622] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.147628] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.147632] pci 0000:00:01.0:   bridge window [mem 0xd8000000-0xdeffffff]
[    0.147634] pci 0000:00:01.0:   bridge window [mem 0xc8000000-0xcfffffff pref]
[    0.147682] pci 0000:00:02.0: PCI bridge to [bus 02]
[    0.147733] pci 0000:00:03.0: PCI bridge to [bus 03]
[    0.147782] pci 0000:00:04.0: PCI bridge to [bus 04]
[    0.147793] pci_bus 0000:05: extended config space not accessible
[    0.147846] pci 0000:00:11.0: PCI bridge to [bus 05]
[    0.148888] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.148993] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.149097] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.149200] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.149303] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.149407] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.149510] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.149611] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15), disabled.
[    0.149714] ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.149930] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[    0.149933] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.149934] pci 0000:01:00.0: vgaarb: bridge control possible
[    0.149935] vgaarb: loaded
[    0.150020] pps_core: LinuxPPS API ver. 1 registered
[    0.150021] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.150024] PTP clock support registered
[    0.150034] EDAC MC: Ver: 3.0.0
[    0.150242] PCI: Using ACPI for IRQ routing
[    0.158539] PCI: pci_cache_line_size set to 64 bytes
[    0.158583] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.158585] e820: reserve RAM buffer [mem 0xc7fd0000-0xc7ffffff]
[    0.158859] clocksource: Switched to clocksource refined-jiffies
[    0.177727] VFS: Disk quotas dquot_6.6.0
[    0.177753] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.177918] AppArmor: AppArmor Filesystem Enabled
[    0.177950] pnp: PnP ACPI init
[    0.178046] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.178298] pnp 00:01: [dma 0 disabled]
[    0.178363] pnp 00:01: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.178572] pnp 00:02: [dma 0 disabled]
[    0.178663] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.178915] pnp 00:03: [dma 2]
[    0.178971] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.179237] pnp 00:04: [dma 0 disabled]
[    0.179348] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.179721] system 00:05: [io  0x04d0-0x04d1] has been reserved
[    0.179724] system 00:05: [io  0x4000-0x40bf] could not be reserved
[    0.179726] system 00:05: [io  0x40c0-0x40df] has been reserved
[    0.179728] system 00:05: [io  0x0400-0x040f] has been reserved
[    0.179730] system 00:05: [io  0x0480-0x048f] has been reserved
[    0.179732] system 00:05: [mem 0xffb00000-0xffb7ffff] has been reserved
[    0.179735] system 00:05: [mem 0xfff80000-0xffffffff] has been reserved
[    0.179737] system 00:05: [mem 0xfec10000-0xfec10fff] could not be reserved
[    0.179739] system 00:05: [mem 0xfec20000-0xfec20fff] has been reserved
[    0.179741] system 00:05: [mem 0xfe000000-0xfe0000ff] has been reserved
[    0.179746] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.179857] system 00:06: [mem 0xffb80000-0xffbfffff] has been reserved
[    0.179859] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.179861] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.179866] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.180054] system 00:07: [io  0x0a00-0x0a0f] has been reserved
[    0.180056] system 00:07: [io  0x0a10-0x0a1f] has been reserved
[    0.180061] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.180140] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
[    0.180145] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.180345] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.180347] system 00:09: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.180349] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.180351] system 00:09: [mem 0x00100000-0xc7ffffff] could not be reserved
[    0.180356] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.180522] pnp: PnP ACPI: found 10 devices
[    0.187159] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.187174] clocksource: Switched to clocksource acpi_pm
[    0.187198] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.187203] pci 0000:00:01.0:   bridge window [mem 0xd8000000-0xdeffffff]
[    0.187206] pci 0000:00:01.0:   bridge window [mem 0xc8000000-0xcfffffff pref]
[    0.187209] pci 0000:00:02.0: PCI bridge to [bus 02]
[    0.187215] pci 0000:00:03.0: PCI bridge to [bus 03]
[    0.187220] pci 0000:00:04.0: PCI bridge to [bus 04]
[    0.187226] pci 0000:00:11.0: PCI bridge to [bus 05]
[    0.187236] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.187237] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.187239] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.187241] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window]
[    0.187243] pci_bus 0000:00: resource 8 [mem 0xc8000000-0xffffffff window]
[    0.187244] pci_bus 0000:01: resource 1 [mem 0xd8000000-0xdeffffff]
[    0.187246] pci_bus 0000:01: resource 2 [mem 0xc8000000-0xcfffffff pref]
[    0.187366] NET: Registered protocol family 2
[    0.187592] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[    0.187633] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.187795] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.188016] TCP: Hash tables configured (established 32768 bind 32768)
[    0.188016] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.188016] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.188016] NET: Registered protocol family 1
[    0.188016] NET: Registered protocol family 44
[    0.188016] pci 0000:00:00.0: Enabling HT MSI Mapping
[    0.188016] pci 0000:00:01.0: Enabling HT MSI Mapping
[    0.188016] pci 0000:00:02.0: Enabling HT MSI Mapping
[    0.188016] pci 0000:00:03.0: Enabling HT MSI Mapping
[    0.188016] pci 0000:00:04.0: Enabling HT MSI Mapping
[    0.688090] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x6c1 took 490941 usecs
[    0.776077] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x6c1 took 85913 usecs
[    0.856076] pci 0000:00:13.2: quirk_usb_early_handoff+0x0/0x6c1 took 78112 usecs
[    0.856213] PCI: CLS mismatch (64 != 32), using 64 bytes
[    0.856248] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.856315] Unpacking initramfs...
[    1.779838] Freeing initrd memory: 35280K
[    1.780213] PCI-DMA: Disabling AGP.
[    1.780293] PCI-DMA: aperture base @ bc000000 size 65536 KB
[    1.780293] PCI-DMA: using GART IOMMU.
[    1.780297] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    1.784477] Initialise system trusted keyrings
[    1.784493] Key type blacklist registered
[    1.784571] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[    1.787056] zbud: loaded
[    2.075897] Key type asymmetric registered
[    2.075900] Asymmetric key parser 'x509' registered
[    2.075922] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    2.075970] io scheduler noop registered
[    2.075971] io scheduler deadline registered
[    2.076067] io scheduler cfq registered (default)
[    2.076069] io scheduler mq-deadline registered
[    2.076716] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    2.076749] ACPI: duty_cycle spans bit 4
[    2.076938] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.097405] 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    2.117959] 00:02: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    2.118399] Linux agpgart interface v0.103
[    2.118442] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    2.118443] AMD IOMMUv2 functionality not available on this system
[    2.118599] i8042: PNP: No PS/2 controller found.
[    2.118600] i8042: Probing ports directly.
[    2.121113] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.121160] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.121285] mousedev: PS/2 mouse device common for all mice
[    2.121336] rtc_cmos 00:00: RTC can wake from S4
[    2.121468] rtc_cmos 00:00: registered as rtc0
[    2.121494] rtc_cmos 00:00: alarms up to one month, 114 bytes nvram
[    2.121519] ledtrig-cpu: registered to indicate activity on CPUs
[    2.122235] NET: Registered protocol family 10
[    2.135300] Segment Routing with IPv6
[    2.135337] mip6: Mobile IPv6
[    2.135340] NET: Registered protocol family 17
[    2.135387] mpls_gso: MPLS GSO support
[    2.135498] mce: Using 5 MCE banks
[    2.135693] registered taskstats version 1
[    2.135694] Loading compiled-in X.509 certificates
[    2.203212] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[    2.203234] Loaded X.509 cert 'Debian Secure Boot Signer 2020: 00b55eb3b9'
[    2.203263] zswap: loaded using pool lzo/zbud
[    2.203327] AppArmor: AppArmor sha1 policy hashing enabled
[    2.203828] rtc_cmos 00:00: setting system clock to 2020-12-13 10:32:14 UTC (1607855534)
[    2.203868] Unstable clock detected, switching default tracing clock to "global"
               If you want to keep using the local clock, then add:
                 "trace_clock=local"
               on the kernel command line
[    2.207333] Freeing unused kernel image memory: 1596K
[    2.216041] Write protecting the kernel read-only data: 16384k
[    2.217423] Freeing unused kernel image memory: 2028K
[    2.217902] Freeing unused kernel image memory: 784K
[    2.234078] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.234080] Run /init as init process
[    2.370037] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    2.370067] ACPI: Power Button [PWRB]
[    2.370466] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    2.370480] ACPI: Power Button [PWRF]
[    2.395837] Floppy drive(s): fd0 is 1.44M
[    2.405910] uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
[    2.439940] FDC 0 is a post-1991 82077
[    2.554891] SCSI subsystem initialized
[    2.626984] ACPI: bus type USB registered
[    2.627016] usbcore: registered new interface driver usbfs
[    2.627030] usbcore: registered new interface driver hub
[    2.630508] uli526x 0000:00:12.0 eth0: ULi M5263 at pci0000:00:12.0, 00:16:17:92:65:bb, irq 20
[    2.630682] ali1535_smbus 0000:00:15.1: enabling device (0000 -> 0001)
[    2.630688] ali1535_smbus 0000:00:15.1: ALI1535_smb region uninitialized - upgrade BIOS?
[    2.630690] ali1535_smbus 0000:00:15.1: ALI1535 not detected, module not inserted.
[    2.632130] ali15x3_smbus 0000:00:15.1: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[    2.632187] ali15x3_smbus 0000:00:15.1: ALI15X3 not detected, module not inserted.
[    2.632388] usbcore: registered new device driver usb
[    2.651938] uli526x 0000:00:12.0 enp0s18: renamed from eth0
[    2.655045] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.682025] ehci-pci: EHCI PCI platform driver
[    2.682197] ehci-pci 0000:00:13.3: EHCI Host Controller
[    2.682206] ehci-pci 0000:00:13.3: new USB bus registered, assigned bus number 1
[    2.682219] ehci-pci 0000:00:13.3: debug port 1
[    2.682285] ehci-pci 0000:00:13.3: irq 23, io mem 0xd7fef800
[    2.682962] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.689581] libata version 3.00 loaded.
[    2.696079] ehci-pci 0000:00:13.3: USB 2.0 started, EHCI 1.00
[    2.696180] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    2.696182] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.696184] usb usb1: Product: EHCI Host Controller
[    2.696185] usb usb1: Manufacturer: Linux 4.19.0-12-amd64 ehci_hcd
[    2.696187] usb usb1: SerialNumber: 0000:00:13.3
[    2.696372] hub 1-0:1.0: USB hub found
[    2.696382] hub 1-0:1.0: 8 ports detected
[    2.699378] ohci-pci: OHCI PCI platform driver
[    2.699537] ohci-pci 0000:00:13.0: OHCI PCI host controller
[    2.699545] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2
[    2.699604] ohci-pci 0000:00:13.0: irq 17, io mem 0xd7fee000
[    2.709223] scsi host0: pata_ali
[    2.710292] ahci 0000:00:16.1: version 3.0
[    2.710473] ahci 0000:00:16.1: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[    2.710477] ahci 0000:00:16.1: flags: ncq sntf ilck pm led clo pmp pio slum part
[    2.717553] scsi host1: pata_ali
[    2.717663] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[    2.717665] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[    2.719903] scsi host2: ahci
[    2.725236] scsi host3: ahci
[    2.725702] scsi host4: ahci
[    2.731525] scsi host5: ahci
[    2.731700] ata3: SATA max UDMA/133 abar m1024@0xd7fef400 port 0xd7fef500 irq 21
[    2.731703] ata4: SATA max UDMA/133 abar m1024@0xd7fef400 port 0xd7fef580 irq 21
[    2.731705] ata5: SATA max UDMA/133 abar m1024@0xd7fef400 port 0xd7fef600 irq 21
[    2.731706] ata6: SATA max UDMA/133 abar m1024@0xd7fef400 port 0xd7fef680 irq 21
[    2.758119] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    2.758123] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.758124] usb usb2: Product: OHCI PCI host controller
[    2.758126] usb usb2: Manufacturer: Linux 4.19.0-12-amd64 ohci_hcd
[    2.758127] usb usb2: SerialNumber: 0000:00:13.0
[    2.758507] hub 2-0:1.0: USB hub found
[    2.758518] hub 2-0:1.0: 3 ports detected
[    2.759035] ohci-pci 0000:00:13.1: OHCI PCI host controller
[    2.759042] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 3
[    2.759095] ohci-pci 0000:00:13.1: irq 18, io mem 0xd7fed000
[    2.854503] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    2.854506] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.854508] usb usb3: Product: OHCI PCI host controller
[    2.854509] usb usb3: Manufacturer: Linux 4.19.0-12-amd64 ohci_hcd
[    2.854511] usb usb3: SerialNumber: 0000:00:13.1
[    2.854912] hub 3-0:1.0: USB hub found
[    2.854923] hub 3-0:1.0: 3 ports detected
[    2.855472] ohci-pci 0000:00:13.2: OHCI PCI host controller
[    2.855481] ohci-pci 0000:00:13.2: new USB bus registered, assigned bus number 4
[    2.855538] ohci-pci 0000:00:13.2: irq 19, io mem 0xd7fec000
[    2.895138] nouveau 0000:01:00.0: NVIDIA NV43 (043100a4)
[    2.919778] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    2.919780] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.919782] usb usb4: Product: OHCI PCI host controller
[    2.919783] usb usb4: Manufacturer: Linux 4.19.0-12-amd64 ohci_hcd
[    2.919784] usb usb4: SerialNumber: 0000:00:13.2
[    2.920209] hub 4-0:1.0: USB hub found
[    2.920219] hub 4-0:1.0: 3 ports detected
[    2.939776] nouveau 0000:01:00.0: bios: version 05.43.02.57.00
[    2.941259] nouveau 0000:01:00.0: fb: 128 MiB DDR1
[    2.993441] [TTM] Zone  kernel: Available graphics memory: 2020904 kiB
[    2.993442] [TTM] Initializing pool allocator
[    2.993448] [TTM] Initializing DMA pool allocator
[    2.993472] nouveau 0000:01:00.0: DRM: VRAM: 124 MiB
[    2.993473] nouveau 0000:01:00.0: DRM: GART: 512 MiB
[    2.993477] nouveau 0000:01:00.0: DRM: TMDS table version 1.1
[    2.993479] nouveau 0000:01:00.0: DRM: DCB version 3.0
[    2.993482] nouveau 0000:01:00.0: DRM: DCB outp 00: 01000300 00000028
[    2.993485] nouveau 0000:01:00.0: DRM: DCB outp 01: 04011322 00000000
[    2.993487] nouveau 0000:01:00.0: DRM: DCB outp 02: 04011320 00000028
[    2.993488] nouveau 0000:01:00.0: DRM: DCB outp 03: 020223f1 0004c080
[    2.993490] nouveau 0000:01:00.0: DRM: DCB conn 00: 0000
[    2.993492] nouveau 0000:01:00.0: DRM: DCB conn 01: 2130
[    2.993493] nouveau 0000:01:00.0: DRM: DCB conn 02: 0210
[    2.993495] nouveau 0000:01:00.0: DRM: DCB conn 03: 0211
[    2.993497] nouveau 0000:01:00.0: DRM: DCB conn 04: 0213
[    2.993782] nouveau 0000:01:00.0: DRM: Saving VGA fonts
[    3.055783] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.055785] [drm] Driver supports precise vblank timestamp query.
[    3.058519] ata4: SATA link down (SStatus 0 SControl 300)
[    3.058599] nouveau 0000:01:00.0: DRM: MM: using M2MF for buffer copies
[    3.058613] nouveau 0000:01:00.0: DRM: Setting dpms mode 3 on TV encoder (output 3)
[    3.063634] ata5: SATA link down (SStatus 0 SControl 300)
[    3.068692] ata6: SATA link down (SStatus 0 SControl 300)
[    3.080285] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-4165B, DL03, max UDMA/33
[    3.080289] ata2.00: WARNING: ATAPI DMA disabled for reliability issues.  It can be enabled
[    3.080290] ata2.00: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
[    3.080294] ata2.01: ATAPI: HL-DT-ST GCE-8525B, 1.03, max UDMA/33
[    3.080296] ata2.01: WARNING: ATAPI DMA disabled for reliability issues.  It can be enabled
[    3.080297] ata2.01: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
[    3.141666] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-4165B DL03 PQ: 0 ANSI: 5
[    3.168417] scsi 1:0:1:0: CD-ROM            HL-DT-ST CD-RW GCE-8525B  1.03 PQ: 0 ANSI: 5
[    3.192327] nouveau 0000:01:00.0: DRM: allocated 1280x1024 fb: 0x9000, bo (____ptrval____)
[    3.192748] fbcon: nouveaufb (fb0) is primary device
[    3.220041] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.220595] ata3.00: ATA-9: WDC WD10EZRZ-00HTKB0, 01.01A01, max UDMA/133
[    3.220597] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    3.221212] ata3.00: configured for UDMA/133
[    3.267236] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.267239] cdrom: Uniform CD-ROM driver Revision: 3.20
[    3.267894] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    3.268867] sr 1:0:1:0: [sr1] scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
[    3.269467] sr 1:0:1:0: Attached scsi CD-ROM sr1
[    3.271067] scsi 2:0:0:0: Direct-Access     ATA      WDC WD10EZRZ-00H 1A01 PQ: 0 ANSI: 5
[    3.277660] sd 2:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    3.277663] sd 2:0:0:0: [sda] 4096-byte physical blocks
[    3.277673] sd 2:0:0:0: [sda] Write Protect is off
[    3.277675] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.277691] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.323727]  sda: sda1 sda2 sda3 sda4 < sda5 >
[    3.324284] sd 2:0:0:0: [sda] Attached SCSI disk
[    3.353476] nouveau 0000:01:00.0: DRM: 0xD590: Parsing digital output script table
[    3.403135] usb 4-2: new full-speed USB device number 2 using ohci-pci
[    3.403929] Console: switching to colour frame buffer device 160x64
[    3.405065] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[    3.405187] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 0
[    3.665769] usb 4-2: New USB device found, idVendor=046d, idProduct=c534, bcdDevice=29.01
[    3.665773] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.665774] usb 4-2: Product: USB Receiver
[    3.665776] usb 4-2: Manufacturer: Logitech
[    3.682321] random: fast init done
[    3.688318] hidraw: raw HID events driver (C) Jiri Kosina
[    3.712141] usbcore: registered new interface driver usbhid
[    3.712143] usbhid: USB HID core driver
[    3.715199] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.2/usb4/4-2/4-2:1.0/0003:046D:C534.0001/input/input5
[    3.772732] hid-generic 0003:046D:C534.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:13.2-2/input0
[    3.773675] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:13.2/usb4/4-2/4-2:1.1/0003:046D:C534.0002/input/input6
[    3.774209] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:13.2/usb4/4-2/4-2:1.1/0003:046D:C534.0002/input/input7
[    3.832373] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:13.2/usb4/4-2/4-2:1.1/0003:046D:C534.0002/input/input8
[    3.832863] hid-generic 0003:046D:C534.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.2-2/input1
[    4.113695] PM: Image not found (code -22)
[    4.271242] cryptd: max_cpu_qlen set to 1000
[    4.371709] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[    5.585564] systemd[1]: Inserted module 'autofs4'
[    5.668752] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    5.668901] systemd[1]: Detected architecture x86-64.
[    5.680298] systemd[1]: Set hostname to <tatarinovolg>.
[    6.007723] random: crng init done
[    7.766140] systemd[1]: Listening on udev Kernel Socket.
[    7.766397] systemd[1]: Listening on Journal Socket (/dev/log).
[    7.767652] systemd[1]: Created slice system-tor.slice.
[    7.768105] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    7.768301] systemd[1]: Listening on fsck to fsckd communication Socket.
[    7.768341] systemd[1]: Reached target Remote File Systems.
[    7.768439] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    7.943602] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[    8.239659] lp: driver loaded but no devices found
[    8.298974] ppdev: user-space parallel port driver
[    8.326559] parport_pc 00:04: reported by Plug and Play ACPI
[    8.326641] parport0: PC-style at 0x378, irq 7 [PCSPP]
[    8.420208] lp0: using parport0 (interrupt-driven).
[    8.566298] systemd-journald[204]: Received request to flush runtime journal from PID 1
[    9.324778] alim7101_wdt: Steve Hill <steve@navaho.co.uk>
[    9.324790] alim7101_wdt: ALi 1543 South-Bridge not present - WDT not set
[    9.391682] sr 1:0:0:0: Attached scsi generic sg0 type 5
[    9.392840] sr 1:0:1:0: Attached scsi generic sg1 type 5
[    9.392915] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    9.407331] input: PC Speaker as /devices/platform/pcspkr/input/input11
[    9.465577] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[    9.465587] k8temp 0000:00:18.3: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[    9.883885] snd_hda_intel 0000:00:14.0: CORB reset timeout#1, CORBRP = 0
[   10.032933] snd_hda_codec_generic hdaudioC0D0: autoconfig for Generic: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[   10.032937] snd_hda_codec_generic hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   10.032939] snd_hda_codec_generic hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   10.032941] snd_hda_codec_generic hdaudioC0D0:    mono: mono_out=0x0
[   10.032942] snd_hda_codec_generic hdaudioC0D0:    inputs:
[   10.032944] snd_hda_codec_generic hdaudioC0D0:      Rear Mic=0x18
[   10.032946] snd_hda_codec_generic hdaudioC0D0:      Front Mic=0x19
[   10.032948] snd_hda_codec_generic hdaudioC0D0:      Line=0x1a
[   10.032949] snd_hda_codec_generic hdaudioC0D0:      CD=0x1c
[   10.082882] input: HDA ULI M5461 Rear Mic as /devices/pci0000:00/0000:00:14.0/sound/card0/input12
[   10.083012] input: HDA ULI M5461 Front Mic as /devices/pci0000:00/0000:00:14.0/sound/card0/input13
[   10.083089] input: HDA ULI M5461 Line as /devices/pci0000:00/0000:00:14.0/sound/card0/input14
[   10.083167] input: HDA ULI M5461 Line Out Front as /devices/pci0000:00/0000:00:14.0/sound/card0/input15
[   10.085995] input: HDA ULI M5461 Line Out Surround as /devices/pci0000:00/0000:00:14.0/sound/card0/input16
[   10.086089] input: HDA ULI M5461 Line Out CLFE as /devices/pci0000:00/0000:00:14.0/sound/card0/input17
[   10.086165] input: HDA ULI M5461 Line Out Side as /devices/pci0000:00/0000:00:14.0/sound/card0/input18
[   10.086243] input: HDA ULI M5461 Front Headphone as /devices/pci0000:00/0000:00:14.0/sound/card0/input19
[   10.521957] kvm: Nested Virtualization enabled
[   10.599249] MCE: In-kernel MCE decoding enabled.
[   10.639069] EDAC amd64: Node 0: DRAM ECC disabled.
[   10.639072] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   10.848239] powernow_k8: [Firmware Bug]: No PSB or ACPI _PSS objects
[   10.848261] powernow_k8: Make sure that your BIOS is up to date and Cool'N'Quiet support is enabled in BIOS setup
[   11.032197] Adding 11718652k swap on /dev/sda2.  Priority:-2 extents:1 across:11718652k FS
[   11.969679] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   12.067241] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   12.943451] audit: type=1400 audit(1607855545.235:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=382 comm="apparmor_parser"
[   12.943458] audit: type=1400 audit(1607855545.235:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=382 comm="apparmor_parser"
[   12.943461] audit: type=1400 audit(1607855545.235:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=382 comm="apparmor_parser"
[   12.970993] audit: type=1400 audit(1607855545.263:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=383 comm="apparmor_parser"
[   13.049280] audit: type=1400 audit(1607855545.343:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=384 comm="apparmor_parser"
[   13.088843] audit: type=1400 audit(1607855545.383:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="torbrowser_firefox" pid=386 comm="apparmor_parser"
[   13.106095] audit: type=1400 audit(1607855545.399:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=387 comm="apparmor_parser"
[   13.119632] audit: type=1400 audit(1607855545.411:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/x86_64-linux-gnu/lightdm/lightdm-guest-session" pid=388 comm="apparmor_parser"
[   13.119638] audit: type=1400 audit(1607855545.411:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/x86_64-linux-gnu/lightdm/lightdm-guest-session//chromium" pid=388 comm="apparmor_parser"
[   13.123493] audit: type=1400 audit(1607855545.415:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=389 comm="apparmor_parser"
[   17.855607] IPv6: ADDRCONF(NETDEV_UP): enp0s18: link is not ready
[   17.858568] IPv6: ADDRCONF(NETDEV_UP): enp0s18: link is not ready
[   20.936386] uli526x 0000:00:12.0 enp0s18: NIC Link is Up 100 Mbps Full duplex
[   20.936410] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s18: link becomes ready
[   66.626348] nouveau 0000:01:00.0: DRM: 0xD597: Parsing digital output script table


Cообщение объединено 13 декабря 2020, 13:46:13

Сейчас попробую найти мышь и клаву ps2 для загрузки на 4.19.0-13-64.
usb мышь genius тоже не работает.

Cообщение объединено 13 декабря 2020, 15:05:00

Сейчас попробовал подключить по USB проводную мышь - на 4.19.0-13-amd64 не работает. Флешку в том же порту видит. Клавиатура ps2 работает. Загрузился c liveCD xubuntu-18.04.5-desktop-amd64  - combo MK295 работает. Дело в драйверах на материнку что-ли?

ferum

Загрузитесь со старым ядром, удалите полностью новое и очистие кеш пакетов. Позже система обновится и будет всё ок.
Русские дебианщики против цифрового слабоумия !

Tatarinovolg

1. Удалил через synaptic ядра 4.19.0-13-amd64 и 5.9.0-0.bpo.2-amd64   
2. Закомментировал в  sources.list строку deb http://deb.debian.org/debian buster-backports main
3. Выполнил команды apt-get autoremove и apt-get clean
4. Перегрузил.
Теперь старое ядро 4.19.0-12. Все работает.
А "позже обновится" - это следующее обновление 10.8 ?
Настораживает что при загрузке из liveCD debian 10.7  xfce (4.19.0-13-amd64) подкдючение к портам usb тоже не работает.

ferum

Цитата: Tatarinovolg от 13 декабря 2020, 18:06:26А "позже обновится" - это следующее обновление 10.8 ?
Не обязательно, если действительно допущена ошибка её пофиксят и обновление ядра выйдет раньше, В прочем у меня на 2х разных компах проблем нет.
Русские дебианщики против цифрового слабоумия !

Tatarinovolg

Спасибо Вам за помощь.
У меня нет глубоких познаний в Линукс, но есть подозрение, что могли выключить поддержку этой материнки. У меня давно на старом ноуте ASUS K50C что-то подобное было. Вроде на 14 ubunte перестали поддерживать видеочип mirage. Дальше были танцы с бубнами которые закончились ничем.