Ошибки при smartctl

[sCode]

Решил проверить диск с помощью smartctl, вот что выдало:
[spoiler:2eddf0yl]smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST3160023AS
Serial Number:    4LJ1FK6A
Firmware Version: 3.00
User Capacity:    160 041 885 696 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Thu Mar  3 09:44:09 2011 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)   Offline data collection activity
               was completed without error.
               Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)   The previous self-test routine completed
               without error or no self-test has ever
               been run.
Total time to complete Offline
data collection:        ( 430) seconds.
Offline data collection
capabilities:           (0x5b) SMART execute Offline immediate.
               Auto Offline data collection on/off support.
               Suspend Offline collection upon new
               command.
               Offline surface scan supported.
               Self-test supported.
               No Conveyance Self-test supported.
               Selective Self-test supported.
SMART capabilities:            (0x0003)   Saves SMART data before entering
               power-saving mode.
               Supports SMART auto save timer.
Error logging capability:        (0x01)   Error logging supported.
               No General Purpose Logging support.
Short self-test routine
recommended polling time:     (   1) minutes.
Extended self-test routine
recommended polling time:     (  94) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   058   042   006    Pre-fail  Always       -       209157456
  3 Spin_Up_Time            0x0003   098   096   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4905
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   079   050   030    Pre-fail  Always       -       43824999393
  9 Power_On_Hours          0x0032   082   082   000    Old_age   Always       -       15877
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   095   095   020    Old_age   Always       -       5703
194 Temperature_Celsius     0x0022   035   046   000    Old_age   Always       -       35 (0 12 0 0)
195 Hardware_ECC_Recovered  0x001a   058   042   000    Old_age   Always       -       209157456
197 Current_Pending_Sector  0x0012   097   091   000    Old_age   Always       -       59
198 Offline_Uncorrectable   0x0010   097   091   000    Old_age   Offline      -       59
199 UDMA_CRC_Error_Count    0x003e   200   199   000    Old_age   Always       -       1
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 2572 (device log contains only the most recent five errors)
   CR = Command Register [HEX]
   FR = Features Register [HEX]
   SC = Sector Count Register [HEX]
   SN = Sector Number Register [HEX]
   CL = Cylinder Low Register [HEX]
   CH = Cylinder High Register [HEX]
   DH = Device/Head Register [HEX]
   DC = Device Command Register [HEX]
   ER = Error register [HEX]
   ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2572 occurred at disk power-on lifetime: 15364 hours (640 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 68 e7 15 60 e0  Error: UNC at LBA = 0x006015e7 = 6297063

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 ff 7e d1 15 60 e0 00      00:10:49.704  READ VERIFY SECTOR(S) EXT
  42 ff 7e 53 15 60 e0 00      00:10:49.703  READ VERIFY SECTOR(S) EXT
  42 ff 7e d5 14 60 e0 00      00:10:49.702  READ VERIFY SECTOR(S) EXT
  42 ff 7e 57 14 60 e0 00      00:10:49.701  READ VERIFY SECTOR(S) EXT
  42 ff 7e d9 13 60 e0 00      00:10:49.700  READ VERIFY SECTOR(S) EXT

Error 2571 occurred at disk power-on lifetime: 15364 hours (640 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 38 dd ae 16 e0  Error: UNC at LBA = 0x0016aedd = 1486557

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 ff 7e 97 ae 16 e0 00      00:10:03.546  READ VERIFY SECTOR(S) EXT
  42 ff 7e 19 ae 16 e0 00      00:10:03.544  READ VERIFY SECTOR(S) EXT
  42 ff 7e 9b ad 16 e0 00      00:10:03.543  READ VERIFY SECTOR(S) EXT
  42 ff 7e 1d ad 16 e0 00      00:10:03.542  READ VERIFY SECTOR(S) EXT
  42 ff 7e 9f ac 16 e0 00      00:10:03.557  READ VERIFY SECTOR(S) EXT

Error 2570 occurred at disk power-on lifetime: 15364 hours (640 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 89 dc c0 e0  Error: UNC at LBA = 0x00c0dc89 = 12639369

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 ff 7e 13 dc c0 e0 00      00:09:12.858  READ VERIFY SECTOR(S) EXT
  42 ff 7e 95 db c0 e0 00      00:09:12.857  READ VERIFY SECTOR(S) EXT
  42 ff 7e 17 db c0 e0 00      00:09:12.856  READ VERIFY SECTOR(S) EXT
  42 ff 7e 99 da c0 e0 00      00:09:12.854  READ VERIFY SECTOR(S) EXT
  42 ff 7e 1b da c0 e0 00      00:09:12.853  READ VERIFY SECTOR(S) EXT

Error 2569 occurred at disk power-on lifetime: 15364 hours (640 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 68 e7 15 60 e0  Error: UNC at LBA = 0x006015e7 = 6297063

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 ff 7e d1 15 60 e0 00      00:08:13.260  READ VERIFY SECTOR(S) EXT
  42 ff 7e 53 15 60 e0 00      00:08:13.260  READ VERIFY SECTOR(S) EXT
  42 ff 7e d5 14 60 e0 00      00:08:13.259  READ VERIFY SECTOR(S) EXT
  42 ff 7e 57 14 60 e0 00      00:08:13.258  READ VERIFY SECTOR(S) EXT
  42 ff 7e d9 13 60 e0 00      00:08:13.257  READ VERIFY SECTOR(S) EXT

Error 2568 occurred at disk power-on lifetime: 15364 hours (640 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 38 dd ae 16 e0  Error: UNC at LBA = 0x0016aedd = 1486557

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 ff 7e 97 ae 16 e0 00      00:07:27.171  READ VERIFY SECTOR(S) EXT
  42 ff 7e 19 ae 16 e0 00      00:07:27.169  READ VERIFY SECTOR(S) EXT
  42 ff 7e 9b ad 16 e0 00      00:07:27.168  READ VERIFY SECTOR(S) EXT
  42 ff 7e 1d ad 16 e0 00      00:07:27.167  READ VERIFY SECTOR(S) EXT
  42 ff 7e 9f ac 16 e0 00      00:07:27.182  READ VERIFY SECTOR(S) EXT

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.[/spoiler:2eddf0yl]
Много ошибок... Сколько еще проживет этот диск?

[Indeferend]

ID# ATTRIBUTE_NAME      FLAG    VALUE WORST THRESH TYPE                     RAW_VALUE
1    Raw_Read_Error_Rate 0x000f 058      042      006        Pre-fail Always - 209157456

VALUE это текущее значение (остаток здоровья)
THRESH - это значение при котором умрет

Ну а так копите денег на новый винт, еще как вариант попробовать его форматнуть, и по новой переразметить, смущает то что счетчик
Reallocated Sevtor Count по нулям, обычно когда винт сыпется то тут больше нуля, но бывают случаи когда показаниям смарта верить нельзя, вроде показывает 0 битых секторов а в один прекрасный момент помрет