X на 1/4 экрана

Автор ZigZag, 19 октября 2017, 11:57:09

« назад - далее »

0 Пользователи и 1 гость просматривают эту тему.

ZigZag

Не знаю в какой еще раздел написать, поэтому сюда...

Очень прошу помочь.
Имею приставку 3q AB496HW (старенькая, SoC Allwinner A10). Решил я на нее поставить Debian Jessie+X+kodi 16.1
Собрал ядро 3.4.104, с помощью debootstrap собрал rootfs. u-boot взял от Cubieboard. script.bin с родной android прошивки.
Приставка подключена через HDMI. Система запустилась, модуля ядра цепляются, все настроил, wi-fi поднял, xorg встал, fbturbo (видео драйвер) встал
НО Х запускаются только на 1/4 экрана телевизора!

Уже сломал бубен :( Не знаю в какую сторону рыть. Или в сторону Х или в сторону загрузчика/ядра
Xorg.0.log:
Открыть содержимое (спойлер)
[  8440.156]
X.Org X Server 1.16.4
Release Date: 2014-12-20
[  8440.389] X Protocol Version 11, Revision 0
[  8440.464] Build Operating System: Linux 4.9.0-4-armmp-lpae armv7l Debian
[  8440.541] Current Operating System: Linux mc3q 3.4.104-00136-gd47d367 #1 PREEMPT Tue Oct 17 10:37:23 MSK 2017 armv7l
[  8440.543] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 console=tty2 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:0 consoleblank=0 loglevel=0
[  8440.773] Build Date: 16 October 2017  09:26:27AM
[  8440.854] xorg-server 2:1.16.4-1+deb8u2 (http://www.debian.org/support)
[  8440.928] Current version of pixman: 0.32.6
[  8440.943]    Before reporting problems, check http://wiki.x.org
   to make sure that you have the latest version.
[  8440.943] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[  8440.962] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Oct 19 10:43:36 2017
[  8440.967] (==) Using config file: "/etc/X11/xorg.conf"
[  8440.972] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[  8440.977] (==) No Layout section.  Using the first Screen section.
[  8440.977] (**) |-->Screen "My Screen" (0)
[  8440.977] (**) |   |-->Monitor "My Monitor"
[  8440.984] (**) |   |-->Device "Allwinner A10/A13 FBDEV"
[  8440.985] (==) Automatically adding devices
[  8440.985] (==) Automatically enabling devices
[  8440.985] (==) Automatically adding GPU devices
[  8440.996] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[  8440.996]    Entry deleted from font path.
[  8440.999] (==) FontPath set to:
   /usr/share/fonts/X11/misc,
   /usr/share/fonts/X11/100dpi/:unscaled,
   /usr/share/fonts/X11/75dpi/:unscaled,
   /usr/share/fonts/X11/Type1,
   /usr/share/fonts/X11/100dpi,
   /usr/share/fonts/X11/75dpi,
   built-ins
[  8440.999] (==) ModulePath set to "/usr/lib/xorg/modules"
[  8441.005] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[  8441.005] (II) Loader magic: 0xb6f7bf20
[  8441.005] (II) Module ABI versions:
[  8441.005]    X.Org ANSI C Emulation: 0.4
[  8441.005]    X.Org Video Driver: 18.0
[  8441.005]    X.Org XInput driver : 21.0
[  8441.005]    X.Org Server Extension : 8.0
[  8441.006] (II) xfree86: Adding drm device (/dev/dri/card0)
[  8441.006] (II) xfree86: Adding drm device (/dev/dri/card1)
[  8441.007] (II) no primary bus or device found
[  8441.007]    falling back to /sys/devices/platform/mali_drm.0/drm/card0
[  8441.007] (II) LoadModule: "glx"
[  8441.008] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[  8441.076] (II) Module glx: vendor="X.Org Foundation"
[  8441.077]    compiled for 1.16.4, module version = 1.0.0
[  8441.077]    ABI class: X.Org Server Extension, version 8.0
[  8441.077] (==) AIGLX enabled
[  8441.077] (II) LoadModule: "fbturbo"
[  8441.077] (II) Loading /usr/lib/xorg/modules/drivers/fbturbo_drv.so
[  8441.078] (II) Module fbturbo: vendor="X.Org Foundation"
[  8441.078]    compiled for 1.16.4, module version = 0.5.1
[  8441.078]    Module class: X.Org Video Driver
[  8441.078]    ABI class: X.Org Video Driver, version 18.0
[  8441.078] (II) FBTURBO: driver for framebuffer: fbturbo
[  8441.078] (++) using VT number 1

[  8441.078] (--) controlling tty is VT number 1, auto-enabling KeepTty
[  8441.079] (WW) Falling back to old probe method for fbturbo
[  8441.079] (II) Loading sub module "fbdevhw"
[  8441.079] (II) LoadModule: "fbdevhw"
[  8441.079] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[  8441.082] (II) Module fbdevhw: vendor="X.Org Foundation"
[  8441.082]    compiled for 1.16.4, module version = 0.0.2
[  8441.082]    ABI class: X.Org Video Driver, version 18.0
[  8441.082] (II) FBTURBO(0): using /dev/fb0
[  8441.082] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[  8441.082] (II) FBTURBO(0): Creating default Display subsection in Screen section
   "My Screen" for depth/fbbpp 24/32
[  8441.083] (==) FBTURBO(0): Depth 24, (==) framebuffer bpp 32
[  8441.083] (==) FBTURBO(0): RGB weight 888
[  8441.083] (==) FBTURBO(0): Default visual is TrueColor
[  8441.083] (==) FBTURBO(0): Using gamma correction (1.0, 1.0, 1.0)
[  8441.083] (II) FBTURBO(0): hardware:  (video memory: 7200kB)
[  8441.083] (**) FBTURBO(0): Option "fbdev" "/dev/fb0"
[  8441.083] (**) FBTURBO(0): Option "SwapbuffersWait" "true"
[  8441.084] (II) FBTURBO(0): processor: Late ARM Cortex-A8 (NEON can bypass L1 cache)
[  8441.084] (II) FBTURBO(0): checking modes against framebuffer device...
[  8441.084] (II) FBTURBO(0): checking modes against monitor...
[  8441.084] (--) FBTURBO(0): Virtual size is 1280x720 (pitch 1280)
[  8441.084] (**) FBTURBO(0):  Built-in mode "current": 74.2 MHz, 45.0 kHz, 60.0 Hz
[  8441.084] (II) FBTURBO(0): Modeline "current"x0.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync -csync (45.0 kHz b)
[  8441.084] (==) FBTURBO(0): DPI set to (96, 96)
[  8441.084] (II) Loading sub module "fb"
[  8441.084] (II) LoadModule: "fb"
[  8441.085] (II) Loading /usr/lib/xorg/modules/libfb.so
[  8441.097] (II) Module fb: vendor="X.Org Foundation"
[  8441.097]    compiled for 1.16.4, module version = 1.0.0
[  8441.097]    ABI class: X.Org ANSI C Emulation, version 0.4
[  8441.097] (==) Depth 24 pixmap format is 32 bpp
[  8441.105] (II) FBTURBO(0): using backing store heuristics
[  8441.137] (II) FBTURBO(0): enabled G2D acceleration
[  8441.137] (==) FBTURBO(0): Backing store enabled
[  8441.144] (II) FBTURBO(0): using sunxi disp layers for X video extension
[  8441.145] (II) FBTURBO(0): using hardware cursor
[  8441.145] (II) FBTURBO(0): no 3D acceleration because the driver has been compiled without libUMP
[  8441.145] (II) FBTURBO(0): if this is wrong and needs to be fixed, please check ./configure log
[  8441.145] (==) RandR enabled
[  8441.178] (II) SELinux: Disabled on system
[  8441.183] (II) AIGLX: Screen 0 is not DRI2 capable
[  8441.183] (EE) AIGLX: reverting to software rendering
[  8441.276] (II) AIGLX: Loaded and initialized swrast
[  8441.276] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[  8441.611] (II) config/udev: Adding input device axp20-supplyer (/dev/input/event0)
[  8441.611] (**) axp20-supplyer: Applying InputClass "evdev keyboard catchall"
[  8441.611] (II) LoadModule: "evdev"
[  8441.612] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[  8441.624] (II) Module evdev: vendor="X.Org Foundation"
[  8441.624]    compiled for 1.16.0, module version = 2.9.0
[  8441.624]    Module class: X.Org XInput Driver
[  8441.624]    ABI class: X.Org XInput driver, version 21.0
[  8441.624] (II) Using input driver 'evdev' for 'axp20-supplyer'
[  8441.625] (**) axp20-supplyer: always reports core events
[  8441.625] (**) evdev: axp20-supplyer: Device: "/dev/input/event0"
[  8441.625] (--) evdev: axp20-supplyer: Vendor 0x1 Product 0x1
[  8441.625] (--) evdev: axp20-supplyer: Found keys
[  8441.625] (II) evdev: axp20-supplyer: Configuring as keyboard
[  8441.625] (**) Option "config_info" "udev:/sys/devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0/event0"
[  8441.625] (II) XINPUT: Adding extended input device "axp20-supplyer" (type: KEYBOARD, id 6)
[  8441.625] (**) Option "xkb_rules" "evdev"
[  8441.626] (**) Option "xkb_model" "pc105"
[  8441.626] (**) Option "xkb_layout" "us,ru"
[  8441.626] (**) Option "xkb_variant" ","
[  8441.626] (**) Option "xkb_options" "grp:lctrl_lshift_toggle,grp_led:scroll"
[  8441.748] (II) config/udev: Adding input device USB USB Keyboard (/dev/input/event1)
[  8441.748] (**) USB USB Keyboard: Applying InputClass "evdev keyboard catchall"
[  8441.748] (II) Using input driver 'evdev' for 'USB USB Keyboard'
[  8441.748] (**) USB USB Keyboard: always reports core events
[  8441.748] (**) evdev: USB USB Keyboard: Device: "/dev/input/event1"
[  8441.749] (--) evdev: USB USB Keyboard: Vendor 0x1a2c Product 0x2d23
[  8441.749] (--) evdev: USB USB Keyboard: Found keys
[  8441.749] (II) evdev: USB USB Keyboard: Configuring as keyboard
[  8441.749] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input1/event1"
[  8441.749] (II) XINPUT: Adding extended input device "USB USB Keyboard" (type: KEYBOARD, id 7)
[  8441.749] (**) Option "xkb_rules" "evdev"
[  8441.749] (**) Option "xkb_model" "pc105"
[  8441.749] (**) Option "xkb_layout" "us,ru"
[  8441.749] (**) Option "xkb_variant" ","
[  8441.749] (**) Option "xkb_options" "grp:lctrl_lshift_toggle,grp_led:scroll"
[  8441.752] (II) config/udev: Adding input device USB USB Keyboard (/dev/input/event2)
[  8441.752] (**) USB USB Keyboard: Applying InputClass "evdev keyboard catchall"
[  8441.753] (II) Using input driver 'evdev' for 'USB USB Keyboard'
[  8441.753] (**) USB USB Keyboard: always reports core events
[  8441.753] (**) evdev: USB USB Keyboard: Device: "/dev/input/event2"
[  8441.753] (--) evdev: USB USB Keyboard: Vendor 0x1a2c Product 0x2d23
[  8441.753] (--) evdev: USB USB Keyboard: Found 1 mouse buttons
[  8441.753] (--) evdev: USB USB Keyboard: Found scroll wheel(s)
[  8441.753] (--) evdev: USB USB Keyboard: Found relative axes
[  8441.753] (II) evdev: USB USB Keyboard: Forcing relative x/y axes to exist.
[  8441.753] (--) evdev: USB USB Keyboard: Found absolute axes
[  8441.753] (II) evdev: USB USB Keyboard: Forcing absolute x/y axes to exist.
[  8441.753] (--) evdev: USB USB Keyboard: Found keys
[  8441.753] (II) evdev: USB USB Keyboard: Configuring as mouse
[  8441.754] (II) evdev: USB USB Keyboard: Configuring as keyboard
[  8441.754] (II) evdev: USB USB Keyboard: Adding scrollwheel support
[  8441.754] (**) evdev: USB USB Keyboard: YAxisMapping: buttons 4 and 5
[  8441.754] (**) evdev: USB USB Keyboard: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[  8441.754] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.1/usb2/2-1/2-1.1/2-1.1:1.1/input/input2/event2"
[  8441.754] (II) XINPUT: Adding extended input device "USB USB Keyboard" (type: KEYBOARD, id 8)
[  8441.754] (**) Option "xkb_rules" "evdev"
[  8441.754] (**) Option "xkb_model" "pc105"
[  8441.754] (**) Option "xkb_layout" "us,ru"
[  8441.754] (**) Option "xkb_variant" ","
[  8441.754] (**) Option "xkb_options" "grp:lctrl_lshift_toggle,grp_led:scroll"
[  8441.755] (II) evdev: USB USB Keyboard: initialized for relative axes.
[  8441.755] (WW) evdev: USB USB Keyboard: ignoring absolute axes.
[  8441.756] (**) USB USB Keyboard: (accel) keeping acceleration scheme 1
[  8441.756] (**) USB USB Keyboard: (accel) acceleration profile 0
[  8441.756] (**) USB USB Keyboard: (accel) acceleration factor: 2.000
[  8441.756] (**) USB USB Keyboard: (accel) acceleration threshold: 4
[  8441.758] (II) config/udev: Adding input device 2.4G Wireless Optical Mouse (/dev/input/event3)
[  8441.758] (**) 2.4G Wireless Optical Mouse: Applying InputClass "evdev pointer catchall"
[  8441.758] (II) Using input driver 'evdev' for '2.4G Wireless Optical Mouse'
[  8441.758] (**) 2.4G Wireless Optical Mouse: always reports core events
[  8441.758] (**) evdev: 2.4G Wireless Optical Mouse: Device: "/dev/input/event3"
[  8441.759] (--) evdev: 2.4G Wireless Optical Mouse: Vendor 0x1130 Product 0x1704
[  8441.759] (--) evdev: 2.4G Wireless Optical Mouse: Found 12 mouse buttons
[  8441.759] (--) evdev: 2.4G Wireless Optical Mouse: Found scroll wheel(s)
[  8441.759] (--) evdev: 2.4G Wireless Optical Mouse: Found relative axes
[  8441.759] (--) evdev: 2.4G Wireless Optical Mouse: Found x and y relative axes
[  8441.759] (II) evdev: 2.4G Wireless Optical Mouse: Configuring as mouse
[  8441.759] (II) evdev: 2.4G Wireless Optical Mouse: Adding scrollwheel support
[  8441.759] (**) evdev: 2.4G Wireless Optical Mouse: YAxisMapping: buttons 4 and 5
[  8441.759] (**) evdev: 2.4G Wireless Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[  8441.759] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input3/event3"
[  8441.759] (II) XINPUT: Adding extended input device "2.4G Wireless Optical Mouse" (type: MOUSE, id 9)
[  8441.759] (II) evdev: 2.4G Wireless Optical Mouse: initialized for relative axes.
[  8441.760] (**) 2.4G Wireless Optical Mouse: (accel) keeping acceleration scheme 1
[  8441.760] (**) 2.4G Wireless Optical Mouse: (accel) acceleration profile 0
[  8441.760] (**) 2.4G Wireless Optical Mouse: (accel) acceleration factor: 2.000
[  8441.760] (**) 2.4G Wireless Optical Mouse: (accel) acceleration threshold: 4
[  8441.762] (II) config/udev: Adding input device 2.4G Wireless Optical Mouse (/dev/input/mouse0)
[  8441.762] (II) No input driver specified, ignoring this device.
[  8441.762] (II) This device may have been added with another device file.
[свернуть]


Tammy

Выглядит случайно не похожим образом?
Открыть содержимое (спойлер)
[свернуть]

ZigZag

Цитата: qupl от 19 октября 2017, 21:18:38Код: [Выделить]

xrandr -q
lspci | grep -i vga

xrandr -q - нет вывода вообще
lspci | grep -i vga - не работает. нет pci. это SoC

Теперь вообще ничего не понимаю. Откатился на начальную копию своей сборки. Установил драйвера, Х. И теперь Xorg -configure говорит, что sreen not found

Цитата: Tammy от 20 октября 2017, 20:35:59Выглядит случайно не похожим образом?
Ну...Черный экран и изображение в верхней 1/4 экрана

PS: Теперь пытаюсь собрать ядро https://forum.kodi.tv/showthread.php?tid=254202&pid=2199415#pid2199415
Как применить к исходникам из git linux-sunxi коммиты автора топика по ссылки?

Tammy

В Lakka проблема с разрешением на X96 решилась сменой настройки разрешения именно в самом Android. А затем уже последующей установкой. Может тут так же какие-то настройки из установленного ведроида тянет.

ZigZag

#5
xrandr -q
Открыть содержимое (спойлер)
Screen 0: minimum 1280 x 720, current 1280 x 720, maximum 1280 x 720
default connected 1280x720+0+0 0mm x 0mm
   1280x720      60.00*
[свернуть]

hwinfo --short
Открыть содержимое (спойлер)
cpu:
                       ARMv7 Processor rev 2 (v7l)
keyboard:
  /dev/input/event2    USB Keyboard
mouse:
  /dev/input/mice      Tenx 2.4G Wireless Optical Mouse
monitor:
                       Generic Monitor
network:
  wlan0                Realtek 802.11n WLAN Adapter
network interface:
  wlan0                WLAN network interface
  tunl0                Network Interface
  lo                   Loopback network interface
  eth0                 Ethernet network interface
disk:
  /dev/nand            Disk
  /dev/nandb           Disk
  /dev/nandc           Disk
  /dev/nandd           Disk
  /dev/nande           Disk
  /dev/nandf           Disk
  /dev/nandg           Disk
  /dev/nandh           Disk
  /dev/nandi           Disk
  /dev/nandj           Disk
  /dev/nandk           Disk
  /dev/mmcblk0         Disk
partition:
  /dev/nanda           Partition
  /dev/mmcblk0p1       Partition
  /dev/mmcblk0p2       Partition
hub:
                       Linux 3.4.104-00136-gd47d367 ohci_hcd SW USB2.0 'Open' Host Controller (OHCI) Driver
                       Linux 3.4.104-00136-gd47d367 ehci_hcd SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
                       Linux 3.4.104-00136-gd47d367 sw_hcd-hcd sw_hcd host driver
                       Linux 3.4.104-00136-gd47d367 ehci_hcd SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
                       Genesys Logic USB2.0 Hub
memory:
                       Main Memory
unknown:
                       Serial controller
  /dev/input/event3    USB Keyboard
[свернуть]

Cообщение объединено 23 октября 2017, 20:08:04

откатился на бэкап системы без драйверов (только после начальной настрйки).
Установил драйвера по этой: http://linux-sunxi.org/Mali_binary_driver и этой: http://wiki.lemaker.org/BananaPro/Pi:GPU ссылкам. Собрались без ошибок. xorg.conf взял из ссылок выше. И снова Х стартуют на 1/4 экрана. При этом в логе непонятные ошибки
Открыть содержимое (спойлер)
[    72.922]
X.Org X Server 1.16.4
Release Date: 2014-12-20
[    72.928] X Protocol Version 11, Revision 0
[    72.932] Build Operating System: Linux 4.9.0-4-armmp-lpae armv7l Debian
[    72.937] Current Operating System: Linux mc3q 3.4.104-00136-gd47d367 #1 PREEMPT Mon Oct 23 17:23:28 MSK 2017 armv7l
[    72.939] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 console=tty2 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:0 consoleblank=0 loglevel=0 sunxi_fb_mem_reserve=16
[    72.952] Build Date: 16 October 2017  09:26:27AM
[    72.955] xorg-server 2:1.16.4-1+deb8u2 (http://www.debian.org/support)
[    72.958] Current version of pixman: 0.32.6
[    72.963]    Before reporting problems, check http://wiki.x.org
   to make sure that you have the latest version.
[    72.965] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    72.984] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Jan  1 00:00:58 2010
[    73.039] (==) Using config file: "/etc/X11/xorg.conf"
[    73.044] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    73.094] (==) No Layout section.  Using the first Screen section.
[    73.098] (**) |-->Screen "My Screen" (0)
[    73.099] (**) |   |-->Monitor "My Monitor"
[    73.156] (**) |   |-->Device "Allwinner A10/A13 FBDEV"
[    73.158] (==) Automatically adding devices
[    73.159] (==) Automatically enabling devices
[    73.159] (==) Automatically adding GPU devices
[    73.216] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    73.217]    Entry deleted from font path.
[    73.234] (==) FontPath set to:
   /usr/share/fonts/X11/misc,
   /usr/share/fonts/X11/100dpi/:unscaled,
   /usr/share/fonts/X11/75dpi/:unscaled,
   /usr/share/fonts/X11/Type1,
   /usr/share/fonts/X11/100dpi,
   /usr/share/fonts/X11/75dpi,
   built-ins
[    73.235] (==) ModulePath set to "/usr/lib/xorg/modules"
[    73.236] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[    73.236] (II) Loader magic: 0xb6febf20
[    73.237] (II) Module ABI versions:
[    73.238]    X.Org ANSI C Emulation: 0.4
[    73.238]    X.Org Video Driver: 18.0
[    73.239]    X.Org XInput driver : 21.0
[    73.240]    X.Org Server Extension : 8.0
[    73.252] (II) xfree86: Adding drm device (/dev/dri/card0)
[    73.261] (II) xfree86: Adding drm device (/dev/dri/card1)
[    73.265] (II) no primary bus or device found
[    73.266]    falling back to /sys/devices/platform/mali_drm.0/drm/card0
[    73.267] (II) LoadModule: "glx"
[    73.289] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    73.698] (II) Module glx: vendor="X.Org Foundation"
[    73.699]    compiled for 1.16.4, module version = 1.0.0
[    73.705]    ABI class: X.Org Server Extension, version 8.0
[    73.706] (==) AIGLX enabled
[    73.708] (II) LoadModule: "fbturbo"
[    73.725] (II) Loading /usr/lib/xorg/modules/drivers/fbturbo_drv.so
[    73.775] (II) Module fbturbo: vendor="X.Org Foundation"
[    73.776]    compiled for 1.16.4, module version = 0.5.1
[    73.777]    Module class: X.Org Video Driver
[    73.778]    ABI class: X.Org Video Driver, version 18.0
[    73.783] (II) FBTURBO: driver for framebuffer: fbturbo
[    73.785] (++) using VT number 1

[    73.786] (--) controlling tty is VT number 1, auto-enabling KeepTty
[    73.789] (WW) Falling back to old probe method for fbturbo
[    73.797] (II) Loading sub module "fbdevhw"
[    73.798] (II) LoadModule: "fbdevhw"
[    73.806] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    73.816] (II) Module fbdevhw: vendor="X.Org Foundation"
[    73.817]    compiled for 1.16.4, module version = 0.0.2
[    73.818]    ABI class: X.Org Video Driver, version 18.0
[    73.821] (II) FBTURBO(0): using /dev/fb0
[    73.823] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[    73.825] (II) FBTURBO(0): Creating default Display subsection in Screen section
   "My Screen" for depth/fbbpp 24/32
[    73.826] (==) FBTURBO(0): Depth 24, (==) framebuffer bpp 32
[    73.827] (==) FBTURBO(0): RGB weight 888
[    73.828] (==) FBTURBO(0): Default visual is TrueColor
[    73.829] (==) FBTURBO(0): Using gamma correction (1.0, 1.0, 1.0)
[    73.831] (II) FBTURBO(0): hardware:  (video memory: 14400kB)
[    73.832] (**) FBTURBO(0): Option "fbdev" "/dev/fb0"
[    73.834] (**) FBTURBO(0): Option "SwapbuffersWait" "true"
[    73.835] (**) FBTURBO(0): Option "AccelMethod" "G2D"
[    73.840] (II) FBTURBO(0): processor: Late ARM Cortex-A8 (NEON can bypass L1 cache)
[    73.841] (II) FBTURBO(0): checking modes against framebuffer device...
[    73.842] (II) FBTURBO(0): checking modes against monitor...
[    73.843] (--) FBTURBO(0): Virtual size is 1280x720 (pitch 1280)
[    73.844] (**) FBTURBO(0):  Built-in mode "current": 74.2 MHz, 45.0 kHz, 60.0 Hz
[    73.845] (II) FBTURBO(0): Modeline "current"x0.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync -csync (45.0 kHz b)
[    73.846] (==) FBTURBO(0): DPI set to (96, 96)
[    73.847] (II) Loading sub module "fb"
[    73.848] (II) LoadModule: "fb"
[    73.857] (II) Loading /usr/lib/xorg/modules/libfb.so
[    73.883] (II) Module fb: vendor="X.Org Foundation"
[    73.884]    compiled for 1.16.4, module version = 1.0.0
[    73.885]    ABI class: X.Org ANSI C Emulation, version 0.4
[    73.886] (==) Depth 24 pixmap format is 32 bpp
[    73.918] (II) FBTURBO(0): using backing store heuristics
[    74.045] (II) FBTURBO(0): enabled G2D acceleration
[    74.047] (==) FBTURBO(0): Backing store enabled
[    74.084] (II) FBTURBO(0): using sunxi disp layers for X video extension
[    74.086] (II) FBTURBO(0): using hardware cursor
[    75.778] (II) Loading sub module "dri2"
[    75.779] (II) LoadModule: "dri2"
[    75.784] (II) Module "dri2" already built-in
[    75.887] (II) FBTURBO(0): enabled display controller hardware overlays for DRI2
[    75.887] (II) FBTURBO(0): Wait on SwapBuffers? enabled
[    75.887] (II) FBTURBO(0): [DRI2] Setup complete
[    75.887] (II) FBTURBO(0): [DRI2]   DRI driver: lima
[    75.887] (II) FBTURBO(0): [DRI2]   VDPAU driver: sunxi
[    75.887] (II) FBTURBO(0): using DRI2 integration for Mali GPU (UMP buffers)
[    75.887] (II) FBTURBO(0): Mali binary drivers can only accelerate EGL/GLES
[    75.887] (II) FBTURBO(0): so AIGLX/GLX is expected to fail or fallback to software
[    75.887] (==) RandR enabled
[    75.922] (II) SELinux: Disabled on system
[    75.928] (EE) AIGLX error: dlopen of /usr/lib/arm-linux-gnueabihf/dri/lima_dri.so failed (/usr/lib/arm-linux-gnueabihf/dri/lima_dri.so: cannot open shared object file: No such file or directory)
[    75.928] (EE) AIGLX: reverting to software rendering
[    76.065] (II) AIGLX: Loaded and initialized swrast
[    76.065] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[    76.416] (II) config/udev: Adding input device axp20-supplyer (/dev/input/event0)
[    76.416] (**) axp20-supplyer: Applying InputClass "evdev keyboard catchall"
[    76.416] (II) LoadModule: "evdev"
[    76.416] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    76.428] (II) Module evdev: vendor="X.Org Foundation"
[    76.428]    compiled for 1.16.0, module version = 2.9.0
[    76.428]    Module class: X.Org XInput Driver
[    76.428]    ABI class: X.Org XInput driver, version 21.0
[    76.429] (II) Using input driver 'evdev' for 'axp20-supplyer'
[    76.429] (**) axp20-supplyer: always reports core events
[    76.429] (**) evdev: axp20-supplyer: Device: "/dev/input/event0"
[    76.429] (--) evdev: axp20-supplyer: Vendor 0x1 Product 0x1
[    76.429] (--) evdev: axp20-supplyer: Found keys
[    76.429] (II) evdev: axp20-supplyer: Configuring as keyboard
[    76.429] (**) Option "config_info" "udev:/sys/devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0/event0"
[    76.435] (II) XINPUT: Adding extended input device "axp20-supplyer" (type: KEYBOARD, id 6)
[    76.435] (**) Option "xkb_rules" "evdev"
[    76.435] (**) Option "xkb_model" "pc105"
[    76.435] (**) Option "xkb_layout" "us,ru"
[    76.435] (**) Option "xkb_variant" ","
[    76.435] (**) Option "xkb_options" "grp:lctrl_lshift_toggle,grp_led:scroll"
[    76.568] (II) config/udev: Adding input device 2.4G Wireless Optical Mouse (/dev/input/event1)
[    76.568] (**) 2.4G Wireless Optical Mouse: Applying InputClass "evdev pointer catchall"
[    76.568] (II) Using input driver 'evdev' for '2.4G Wireless Optical Mouse'
[    76.568] (**) 2.4G Wireless Optical Mouse: always reports core events
[    76.568] (**) evdev: 2.4G Wireless Optical Mouse: Device: "/dev/input/event1"
[    76.569] (--) evdev: 2.4G Wireless Optical Mouse: Vendor 0x1130 Product 0x1704
[    76.569] (--) evdev: 2.4G Wireless Optical Mouse: Found 12 mouse buttons
[    76.569] (--) evdev: 2.4G Wireless Optical Mouse: Found scroll wheel(s)
[    76.569] (--) evdev: 2.4G Wireless Optical Mouse: Found relative axes
[    76.569] (--) evdev: 2.4G Wireless Optical Mouse: Found x and y relative axes
[    76.569] (II) evdev: 2.4G Wireless Optical Mouse: Configuring as mouse
[    76.569] (II) evdev: 2.4G Wireless Optical Mouse: Adding scrollwheel support
[    76.569] (**) evdev: 2.4G Wireless Optical Mouse: YAxisMapping: buttons 4 and 5
[    76.569] (**) evdev: 2.4G Wireless Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    76.569] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input1/event1"
[    76.569] (II) XINPUT: Adding extended input device "2.4G Wireless Optical Mouse" (type: MOUSE, id 7)
[    76.570] (II) evdev: 2.4G Wireless Optical Mouse: initialized for relative axes.
[    76.571] (**) 2.4G Wireless Optical Mouse: (accel) keeping acceleration scheme 1
[    76.571] (**) 2.4G Wireless Optical Mouse: (accel) acceleration profile 0
[    76.571] (**) 2.4G Wireless Optical Mouse: (accel) acceleration factor: 2.000
[    76.571] (**) 2.4G Wireless Optical Mouse: (accel) acceleration threshold: 4
[    76.572] (II) config/udev: Adding input device 2.4G Wireless Optical Mouse (/dev/input/mouse0)
[    76.572] (II) No input driver specified, ignoring this device.
[    76.572] (II) This device may have been added with another device file.
[    76.574] (II) config/udev: Adding input device USB USB Keyboard (/dev/input/event2)
[    76.574] (**) USB USB Keyboard: Applying InputClass "evdev keyboard catchall"
[    76.574] (II) Using input driver 'evdev' for 'USB USB Keyboard'
[    76.574] (**) USB USB Keyboard: always reports core events
[    76.574] (**) evdev: USB USB Keyboard: Device: "/dev/input/event2"
[    76.574] (--) evdev: USB USB Keyboard: Vendor 0x1a2c Product 0x2d23
[    76.574] (--) evdev: USB USB Keyboard: Found keys
[    76.575] (II) evdev: USB USB Keyboard: Configuring as keyboard
[    76.575] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input2/event2"
[    76.575] (II) XINPUT: Adding extended input device "USB USB Keyboard" (type: KEYBOARD, id 8)
[    76.575] (**) Option "xkb_rules" "evdev"
[    76.575] (**) Option "xkb_model" "pc105"
[    76.575] (**) Option "xkb_layout" "us,ru"
[    76.575] (**) Option "xkb_variant" ","
[    76.575] (**) Option "xkb_options" "grp:lctrl_lshift_toggle,grp_led:scroll"
[    76.578] (II) config/udev: Adding input device USB USB Keyboard (/dev/input/event3)
[    76.578] (**) USB USB Keyboard: Applying InputClass "evdev keyboard catchall"
[    76.578] (II) Using input driver 'evdev' for 'USB USB Keyboard'
[    76.578] (**) USB USB Keyboard: always reports core events
[    76.578] (**) evdev: USB USB Keyboard: Device: "/dev/input/event3"
[    76.578] (--) evdev: USB USB Keyboard: Vendor 0x1a2c Product 0x2d23
[    76.578] (--) evdev: USB USB Keyboard: Found 1 mouse buttons
[    76.579] (--) evdev: USB USB Keyboard: Found scroll wheel(s)
[    76.579] (--) evdev: USB USB Keyboard: Found relative axes
[    76.579] (II) evdev: USB USB Keyboard: Forcing relative x/y axes to exist.
[    76.579] (--) evdev: USB USB Keyboard: Found absolute axes
[    76.579] (II) evdev: USB USB Keyboard: Forcing absolute x/y axes to exist.
[    76.579] (--) evdev: USB USB Keyboard: Found keys
[    76.579] (II) evdev: USB USB Keyboard: Configuring as mouse
[    76.579] (II) evdev: USB USB Keyboard: Configuring as keyboard
[    76.579] (II) evdev: USB USB Keyboard: Adding scrollwheel support
[    76.579] (**) evdev: USB USB Keyboard: YAxisMapping: buttons 4 and 5
[    76.579] (**) evdev: USB USB Keyboard: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    76.579] (**) Option "config_info" "udev:/sys/devices/platform/sw-ehci.1/usb2/2-1/2-1.2/2-1.2:1.1/input/input3/event3"
[    76.579] (II) XINPUT: Adding extended input device "USB USB Keyboard" (type: KEYBOARD, id 9)
[    76.579] (**) Option "xkb_rules" "evdev"
[    76.579] (**) Option "xkb_model" "pc105"
[    76.579] (**) Option "xkb_layout" "us,ru"
[    76.580] (**) Option "xkb_variant" ","
[    76.580] (**) Option "xkb_options" "grp:lctrl_lshift_toggle,grp_led:scroll"
[    76.581] (II) evdev: USB USB Keyboard: initialized for relative axes.
[    76.581] (WW) evdev: USB USB Keyboard: ignoring absolute axes.
[    76.581] (**) USB USB Keyboard: (accel) keeping acceleration scheme 1
[    76.581] (**) USB USB Keyboard: (accel) acceleration profile 0
[    76.582] (**) USB USB Keyboard: (accel) acceleration factor: 2.000
[    76.582] (**) USB USB Keyboard: (accel) acceleration threshold: 4
[   530.708] (II) evdev: USB USB Keyboard: Close
[   530.756] (II) UnloadModule: "evdev"
[   530.759] (II) evdev: USB USB Keyboard: Close
[   530.781] (II) UnloadModule: "evdev"
[   530.784] (II) evdev: 2.4G Wireless Optical Mouse: Close
[   530.785] (II) UnloadModule: "evdev"
[   530.787] (II) evdev: axp20-supplyer: Close
[   530.789] (II) UnloadModule: "evdev"
[   531.178] (WW) xf86CloseConsole: KDSETMODE failed: Input/output error
[   531.197] (WW) xf86CloseConsole: VT_GETMODE failed: Input/output error
[   531.198] (EE)
Fatal server error:
[   531.199] (EE) xf86CloseConsole: VT_ACTIVATE failed: Input/output error
[   531.201] (EE)
[   531.202] (EE)
Please consult the The X.Org Foundation support
    at http://wiki.x.org
for help.
[   531.203] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[   531.204] (EE)
[   531.206] (EE)
[   531.207] (EE) Backtrace:
[   531.208] (EE)
[   531.251] (EE) Segmentation fault at address 0x4c
[   531.252] (EE)
FatalError re-entered, aborting
[   531.254] (EE) Caught signal 11 (Segmentation fault). Server aborting
[   531.255] (EE)
[свернуть]

vic5710

Цитата: ZigZag от 23 октября 2017, 20:01:4775.928] (EE) AIGLX error: dlopen of /usr/lib/arm-linux-gnueabihf/dri/lima_dri.so failed (/usr/lib/arm-linux-gnueabihf/dri/lima_dri.so: cannot open shared object file: No such file or directory)

sidbar

Kernel command line: disp.screen0_output_mode=EDID:1280x720p60
Devuan GNU/Linux