программная точка доступа Widemac SL-1507N

x3 · 11 июня 2012, 10:52:27

uname -a
Linux dhcppc1 2.6.32-5-686 #1 SMP Sun May 6 04:01:19 UTC 2012 i686 GNU/Linux

debian-6.0.5
Widemac SL-1507N на RaLink RT5370 http://www.sztianhao.com/en/prodetial.php?id=146

Код Выделить

ifconfig
eth0      Link encap:Ethernet  HWaddr 00:e0:c5:57:91:24
          inet addr:192.168.1.3  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::2e0:c5ff:fe57:9124/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1645 errors:0 dropped:0 overruns:0 frame:0
          TX packets:796 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:173836 (169.7 KiB)  TX bytes:121384 (118.5 KiB)
          Interrupt:11 Base address:0xe400

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:560 (560.0 B)  TX bytes:560 (560.0 B)

ra0       Link encap:Ethernet  HWaddr 00:0f:53:87:18:e4
          inet6 addr: fe80::20f:53ff:fe87:18e4/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:74262 (72.5 KiB)  TX bytes:410352 (400.7 KiB)

Код Выделить

iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

ra0       Ralink STA  ESSID:""  Nickname:"RT2870STA"
          Mode:Ad-Hoc  Frequency=2.412 GHz  Cell: 7A:BA:93:E2:E6:F9   
          Bit Rate=150 Mb/s   
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Link Quality=70/100  Signal level:0 dBm  Noise level:0 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Это в режиме Ad-Hoc, по умолчанию, когда делаю ifconfig ra0 up он в режиме auto но тогда даже лампочка на нем не горит.

Код Выделить

iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

ra0       Ralink STA  ESSID:""  Nickname:"RT2870STA"
          Mode:Auto  Frequency=2.412 GHz  Bit Rate=1 Mb/s   
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Link Quality=70/100  Signal level:0 dBm  Noise level:0 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

В режим Master не переводится (в Fedora 17 как подключил она сразу Master)

Код Выделить

iwconfig ra0 mode Master
Error for wireless request "Set Mode" (8B06) :
    SET failed on device ra0 ; Invalid argument.

Код Выделить

dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-45) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sun May 6 04:01:19 UTC 2012
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000077f0000 (usable)
[    0.000000]  BIOS-e820: 00000000077f0000 - 00000000077f3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000077f3000 - 0000000007800000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[    0.000000] DMI 2.2 present.
[    0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0x77f0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CEFFF write-protect
[    0.000000]   CF000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FF8000000 write-back
[    0.000000]   1 base 007800000 mask FFF800000 uncachable
[    0.000000]   2 base 0EE000000 mask FFFC00000 write-combining
[    0.000000]   3 base 0E8000000 mask FFF800000 write-combining
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] initial memory mapped : 0 - 01800000
[    0.000000] init_memory_mapping: 0000000000000000-00000000077f0000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0007400000 page 2M
[    0.000000]  0007400000 - 00077f0000 page 4k
[    0.000000] kernel direct mapping tables up to 77f0000 @ 10000-16000
[    0.000000] RAMDISK: 051e6000 - 05a33d8c
[    0.000000] ACPI: RSDP 000f66b0 00014 (v00 CLE266)
[    0.000000] ACPI: RSDT 077f3040 00028 (v01 CLE266 AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: FACP 077f30c0 00074 (v01 CLE266 AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: DSDT 077f3180 03DF8 (v01 CLE266 AWRDACPI 00001000 MSFT 0100000E)
[    0.000000] ACPI: FACS 077f0000 00040
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 119MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 077f0000
[    0.000000]   low ram: 0 - 077f0000
[    0.000000]   node 0 low ram: 00000000 - 077f0000
[    0.000000]   node 0 bootmap 00012000 - 00012f00
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00077f0000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0001000000 - 00014ccd2c]    TEXT DATA BSS ==> [0001000000 - 00014ccd2c]
[    0.000000]   #4 [00051e6000 - 0005a33d8c]          RAMDISK ==> [00051e6000 - 0005a33d8c]
[    0.000000]   #5 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
[    0.000000]   #6 [00014cd000 - 00014d30b2]              BRK ==> [00014cd000 - 00014d30b2]
[    0.000000]   #7 [0000010000 - 0000012000]          PGTABLE ==> [0000010000 - 0000012000]
[    0.000000]   #8 [0000012000 - 0000013000]          BOOTMAP ==> [0000012000 - 0000013000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000077f0
[    0.000000]   HighMem  0x000077f0 -> 0x000077f0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000077f0
[    0.000000] On node 0 totalpages: 30591
[    0.000000] free_area_init_node: node 0, pgdat c13b48c0, node_mem_map c14d5200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 208 pages used for memmap
[    0.000000]   Normal zone: 26400 pages, LIFO batch:7
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] No local APIC present or hardware disabled
[    0.000000] APIC: disable apic facility
[    0.000000] nr_irqs_gsi: 16
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 7800000 (gap: 7800000:f87f0000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c1800000 s34328 r0 d23016 u4194304
[    0.000000] pcpu-alloc: s34328 r0 d23016 u4194304 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30351
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=2722b8e9-9ed5-411a-af59-a656500715c7 ro quiet
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 107596k/122816k available (2506k kernel code, 14608k reserved, 1326k data, 380k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffd56000 - 0xfffff000   (2724 kB)
[    0.000000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.000000]     vmalloc : 0xc7ff0000 - 0xff3fe000   ( 884 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc77f0000   ( 119 MB)
[    0.000000]       .init : 0xc13bf000 - 0xc141e000   ( 380 kB)
[    0.000000]       .data : 0xc1272b8b - 0xc13be4c4   (1326 kB)
[    0.000000]       .text : 0xc1000000 - 0xc1272b8b   (2506 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:1280
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 800.236 MHz processor.
[    0.004011] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.47 BogoMIPS (lpj=3200944)
[    0.004088] Security Framework initialized
[    0.004113] SELinux:  Disabled at boot.
[    0.004139] Mount-cache hash table entries: 512
[    0.004556] Initializing cgroup subsys ns
[    0.004570] Initializing cgroup subsys cpuacct
[    0.004587] Initializing cgroup subsys devices
[    0.004598] Initializing cgroup subsys freezer
[    0.004681] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
[    0.004694] CPU: L2 Cache: 64K (32 bytes/line)
[    0.004740] Performance Events:
[    0.004755] Checking 'hlt' instruction... OK.
[    0.020706] SMP alternatives: switching to UP code
[    0.037453] Freeing SMP alternatives: 13k freed
[    0.037543] ACPI: Core revision 20090903
[    0.048331] ACPI: setting ELCR to 0200 (from da00)
[    0.052393] Enabling APIC mode:  Flat.  Using 0 I/O APICs
[    0.052405] weird, boot CPU (#0) not listed by the BIOS.
[    0.052414] SMP motherboard not detected.
[    0.052423] Local APIC not detected. Using dummy APIC emulation.
[    0.052432] SMP disabled
[    0.053145] Brought up 1 CPUs
[    0.053159] Total of 1 processors activated (1600.47 BogoMIPS).
[    0.053209] CPU0 attaching NULL sched-domain.
[    0.056291] devtmpfs: initialized
[    0.057950] regulator: core version 0.5
[    0.058174] NET: Registered protocol family 16
[    0.058501] ACPI: bus type pci registered
[    0.064823] PCI: PCI BIOS revision 2.10 entry at 0xfb3f0, last bus=1
[    0.064834] PCI: Using configuration type 1 for base access
[    0.066313] bio: create slab <bio-0> at 0
[    0.068151] ACPI: EC: Look up EC in DSDT
[    0.083980] ACPI: Interpreter enabled
[    0.084016] ACPI: (supports S0 S1 S4 S5)
[    0.084111] ACPI: Using PIC for interrupt routing
[    0.096352] ACPI: No dock devices found.
[    0.096674] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.096825] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xee000000-0xee3fffff]
[    0.097008] pci 0000:00:01.0: supports D1
[    0.097112] pci 0000:00:10.0: reg 20 io port: [0xe900-0xe91f]
[    0.097167] pci 0000:00:10.0: supports D1 D2
[    0.097179] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.097194] pci 0000:00:10.0: PME# disabled
[    0.097276] pci 0000:00:10.1: reg 20 io port: [0xea00-0xea1f]
[    0.097331] pci 0000:00:10.1: supports D1 D2
[    0.097342] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.097355] pci 0000:00:10.1: PME# disabled
[    0.097436] pci 0000:00:10.2: reg 20 io port: [0xe800-0xe81f]
[    0.097491] pci 0000:00:10.2: supports D1 D2
[    0.097502] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.097515] pci 0000:00:10.2: PME# disabled
[    0.097577] pci 0000:00:10.3: reg 10 32bit mmio: [0xee400000-0xee4000ff]
[    0.097654] pci 0000:00:10.3: supports D1 D2
[    0.097665] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.097678] pci 0000:00:10.3: PME# disabled
[    0.097790] HPET not enabled in BIOS. You might try hpet=force boot option
[    0.097812] pci 0000:00:11.0: quirk: region 4000-407f claimed by vt8235 PM
[    0.097827] pci 0000:00:11.0: quirk: region 5000-500f claimed by vt8235 SMB
[    0.097930] pci 0000:00:11.5: reg 10 io port: [0xe000-0xe0ff]
[    0.098008] pci 0000:00:11.5: supports D1 D2
[    0.098072] pci 0000:00:12.0: reg 10 io port: [0xe400-0xe4ff]
[    0.098092] pci 0000:00:12.0: reg 14 32bit mmio: [0xee401000-0xee4010ff]
[    0.098165] pci 0000:00:12.0: supports D1 D2
[    0.098176] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.098190] pci 0000:00:12.0: PME# disabled
[    0.098288] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xe8000000-0xebffffff]
[    0.098309] pci 0000:01:00.0: reg 14 32bit mmio: [0xec000000-0xecffffff]
[    0.098345] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
[    0.098392] pci 0000:01:00.0: supports D1 D2
[    0.098464] pci 0000:00:01.0: bridge 32bit mmio: [0xec000000-0xedffffff]
[    0.098482] pci 0000:00:01.0: bridge 32bit mmio pref: [0xe8000000-0xebffffff]
[    0.098504] pci_bus 0000:00: on NUMA node 0
[    0.098524] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.098673] ACPI Warning for \_SB_.PCI0._PRT: Return Package type mismatch at index 2 - found [NULL Object Descriptor], expected Integer/Reference (20090903/nspredef-1012)
[    0.147022] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *15
[    0.147578] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *14
[    0.148169] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
[    0.148731] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 *12)
[    0.149126] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.149139] vgaarb: loaded
[    0.149438] PCI: Using ACPI for IRQ routing
[    0.149862] Switching to clocksource tsc
[    0.152683] pnp: PnP ACPI init
[    0.152752] ACPI: bus type pnp registered
[    0.162976] pnp: PnP ACPI: found 12 devices
[    0.162989] ACPI: ACPI bus type pnp unregistered
[    0.163003] PnPBIOS: Disabled by ACPI PNP
[    0.163046] system 00:00: iomem range 0xf0000-0xf3fff could not be reserved
[    0.163063] system 00:00: iomem range 0xf4000-0xf7fff could not be reserved
[    0.163080] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[    0.163097] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[    0.163114] system 00:00: iomem range 0x77f0000-0x77fffff could not be reserved
[    0.163133] system 00:00: iomem range 0xffff0000-0xffffffff has been reserved
[    0.163149] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.163166] system 00:00: iomem range 0x100000-0x77effff could not be reserved
[    0.163184] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.163201] system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
[    0.163232] system 00:02: ioport range 0x4000-0x407f has been reserved
[    0.163248] system 00:02: ioport range 0x5000-0x500f has been reserved
[    0.163276] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[    0.163292] system 00:03: ioport range 0x294-0x297 has been reserved
[    0.198667] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.198680] pci 0000:00:01.0:   IO window: disabled
[    0.198698] pci 0000:00:01.0:   MEM window: 0xec000000-0xedffffff
[    0.198716] pci 0000:00:01.0:   PREFETCH window: 0xe8000000-0xebffffff
[    0.198750] pci 0000:00:01.0: setting latency timer to 64
[    0.198769] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.198784] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.198800] pci_bus 0000:01: resource 1 mem: [0xec000000-0xedffffff]
[    0.198815] pci_bus 0000:01: resource 2 pref mem [0xe8000000-0xebffffff]
[    0.198949] NET: Registered protocol family 2
[    0.199322] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200531] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.200677] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.200812] TCP: Hash tables configured (established 4096 bind 4096)
[    0.200823] TCP reno registered
[    0.201132] NET: Registered protocol family 1
[    0.201197] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[    0.202743] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[    0.202756] PCI: setting IRQ 11 as level-triggered
[    0.202777] pci 0000:00:10.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[    0.202794] pci 0000:00:10.0: VIA VLink IRQ fixup, from 15 to 11
[    0.202841] pci 0000:00:10.0: PCI INT A disabled
[    0.204018] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[    0.204035] pci 0000:00:10.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    0.204051] pci 0000:00:10.1: VIA VLink IRQ fixup, from 14 to 11
[    0.204095] pci 0000:00:10.1: PCI INT B disabled
[    0.205295] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[    0.205313] pci 0000:00:10.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    0.205343] pci 0000:00:10.2: PCI INT C disabled
[    0.206606] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
[    0.206617] PCI: setting IRQ 12 as level-triggered
[    0.206636] pci 0000:00:10.3: PCI INT D -> Link[LNKD] -> GSI 12 (level, low) -> IRQ 12
[    0.206700] pci 0000:00:10.3: PCI INT D disabled
[    0.206735] pci 0000:01:00.0: Boot video device
[    0.206922] Unpacking initramfs...
[    1.526001] Freeing initrd memory: 8503k freed
[    1.575083] audit: initializing netlink socket (disabled)
[    1.575134] type=2000 audit(1339393621.572:1): initialized
[    1.591417] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.598377] VFS: Disk quotas dquot_6.5.2
[    1.598679] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.598989] msgmni has been set to 227
[    1.599809] alg: No test for stdrng (krng)
[    1.599947] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.599960] io scheduler noop registered
[    1.599970] io scheduler anticipatory registered
[    1.599979] io scheduler deadline registered
[    1.600233] io scheduler cfq registered (default)
[    1.600803] isapnp: Scanning for PnP cards...
[    1.954810] isapnp: No Plug & Play device found
[    1.960233] Linux agpgart interface v0.103
[    1.960687] agpgart: Detected VIA CLE266 chipset
[    1.961749] agpgart-via 0000:00:00.0: AGP aperture is 4M @ 0xee000000
[    1.961829] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.962006] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.962211] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.963043] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.963325] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.963879] PNP: No PS/2 controller found. Probing ports directly.
[    2.216154] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.216522] mice: PS/2 mouse device common for all mice
[    2.216694] rtc_cmos 00:05: RTC can wake from S4
[    2.216867] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    2.216918] rtc0: alarms up to one year, y3k, 242 bytes nvram
[    2.216963] cpuidle: using governor ladder
[    2.216973] cpuidle: using governor menu
[    2.216991] No iBFT detected.
[    2.218786] TCP cubic registered
[    2.219458] NET: Registered protocol family 10
[    2.223073] Mobile IPv6
[    2.223089] NET: Registered protocol family 17
[    2.223156] Using IPI No-Shortcut mode
[    2.223500] PM: Resume from disk failed.
[    2.223546] registered taskstats version 1
[    2.224261] rtc_cmos 00:05: setting system clock to 2012-06-11 05:47:03 UTC (1339393623)
[    2.224519] Initalizing network drop monitor service
[    2.224635] Freeing unused kernel memory: 380k freed
[    2.226782] Write protecting the kernel text: 2508k
[    2.226896] Write protecting the kernel read-only data: 920k
[    2.309197] udev[46]: starting version 164
[    2.965576] usbcore: registered new interface driver usbfs
   2.966329] usbcore: registered new interface driver hub
[    2.976714] usbcore: registered new device driver usb
[    2.997566] thermal LNXTHERM:01: registered as thermal_zone0
[    2.997605] ACPI: Thermal Zone [THRM] (45 C)
[    3.013089] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.013206] ehci_hcd 0000:00:10.3: PCI INT D -> Link[LNKD] -> GSI 12 (level, low) -> IRQ 12
[    3.013271] ehci_hcd 0000:00:10.3: EHCI Host Controller
[    3.013358] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
[    3.013482] ehci_hcd 0000:00:10.3: irq 12, io mem 0xee400000
[    3.018269] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[    3.018294] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[    3.024275] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00
[    3.024400] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.024415] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.024428] usb usb1: Product: EHCI Host Controller
[    3.024439] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[    3.024450] usb usb1: SerialNumber: 0000:00:10.3
[    3.025058] usb usb1: configuration #1 chosen from 1 choice
[    3.025329] hub 1-0:1.0: USB hub found
[    3.025377] hub 1-0:1.0: 6 ports detected
[    3.029175] via-rhine 0000:00:12.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[    3.029196] via-rhine 0000:00:12.0: VIA VLink IRQ fixup, from 15 to 11
[    3.049784] eth0: VIA Rhine II at 0x1e400, 00:e0:c5:57:91:24, IRQ 11.
[    3.050515] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
[    3.056641] uhci_hcd: USB Universal Host Controller Interface driver
[    3.056846] uhci_hcd 0000:00:10.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[    3.056881] uhci_hcd 0000:00:10.0: UHCI Host Controller
[    3.056952] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[    3.057015] uhci_hcd 0000:00:10.0: irq 11, io base 0x0000e900
[    3.057219] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    3.057233] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.057246] usb usb2: Product: UHCI Host Controller
[    3.057257] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    3.057268] usb usb2: SerialNumber: 0000:00:10.0
[    3.057914] usb usb2: configuration #1 chosen from 1 choice
[    3.058189] hub 2-0:1.0: USB hub found
[    3.058240] hub 2-0:1.0: 2 ports detected
[    3.058471] uhci_hcd 0000:00:10.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    3.058504] uhci_hcd 0000:00:10.1: UHCI Host Controller
[    3.058537] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[    3.058595] uhci_hcd 0000:00:10.1: irq 11, io base 0x0000ea00
[    3.058816] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    3.058830] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.058843] usb usb3: Product: UHCI Host Controller
[    3.058854] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    3.058865] usb usb3: SerialNumber: 0000:00:10.1
[    3.064352] fan PNP0C0B:00: registered as cooling_device0
[    3.064388] ACPI: Fan [FAN] (on)
[    3.065223] usb usb3: configuration #1 chosen from 1 choice
[    3.066451] hub 3-0:1.0: USB hub found
[    3.066507] hub 3-0:1.0: 2 ports detected
[    3.066762] uhci_hcd 0000:00:10.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    3.066796] uhci_hcd 0000:00:10.2: UHCI Host Controller
[    3.066831] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[    3.066891] uhci_hcd 0000:00:10.2: irq 11, io base 0x0000e800
[    3.067096] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    3.067110] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.067123] usb usb4: Product: UHCI Host Controller
[    3.067134] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    3.067146] usb usb4: SerialNumber: 0000:00:10.2
[    3.071148] usb usb4: configuration #1 chosen from 1 choice
[    3.071648] hub 4-0:1.0: USB hub found
[    3.071706] hub 4-0:1.0: 2 ports detected
[    3.336067] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    3.470209] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[    3.470228] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.470241] usb 1-1: Product: Mass Storage Device
[    3.470252] usb 1-1: Manufacturer: JetFlash
[    3.470262] usb 1-1: SerialNumber: 38M7Q1KHRNHFJ4Y5
[    3.472134] usb 1-1: configuration #1 chosen from 1 choice
[    3.583166] SCSI subsystem initialized
[    3.613666] Initializing USB Mass Storage driver...
[    3.614100] scsi0 : SCSI emulation for USB Mass Storage devices
[    3.614892] usbcore: registered new interface driver usb-storage
[    3.614905] USB Mass Storage support registered.
[    3.617848] usb-storage: device found at 2
[    3.617860] usb-storage: waiting for device to settle before scanning
[    3.628080] usb 1-5: new high speed USB device using ehci_hcd and address 3
[    3.778076] usb 1-5: New USB device found, idVendor=148f, idProduct=5370
[    3.778094] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.778108] usb 1-5: Product: 802.11 n WLAN
[    3.778118] usb 1-5: Manufacturer: Ralink
[    3.778128] usb 1-5: SerialNumber: 1.0
[    3.779867] usb 1-5: configuration #1 chosen from 1 choice
[    4.112092] usb 4-2: new low speed USB device using uhci_hcd and address 2
[    4.289999] usb 4-2: New USB device found, idVendor=1c4f, idProduct=0002
[    4.290018] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.290031] usb 4-2: Product: USB Keykoard
[  243.185410] 0x1300 = 00064300
[  253.676063] ra0: no IPv6 routers present
[  254.629245] cfg80211: Using static regulatory domain info
[  254.629266] cfg80211: Regulatory domain: US
[  254.629280]  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  254.629304]  (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[  254.629327]  (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[  254.629350]  (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[  254.629373]  (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[  254.629396]  (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[  254.629419]  (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[  254.631151] cfg80211: Calling CRDA for country: US
[  255.234032] usbcore: registered new interface driver rt2800usb
[  256.504308] #
[  292.955590] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 142
[ 1194.289805] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 142
[ 2518.646400] ERROR!!! RTMPSetTimer failed, Halt in Progress!
[ 2521.636894] (Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc]
[ 2521.897943] RTMP_TimerListAdd: add timer obj c84f08f8!
[ 2521.897971] RTMP_TimerListAdd: add timer obj c84f093c!
[ 2521.897988] RTMP_TimerListAdd: add timer obj c84f0980!
[ 2521.898007] RTMP_TimerListAdd: add timer obj c84f08b4!
[ 2521.898029] RTMP_TimerListAdd: add timer obj c84f07e8!
[ 2521.898046] RTMP_TimerListAdd: add timer obj c84f082c!
[ 2521.898064] RTMP_TimerListAdd: add timer obj c84bb3d0!
[ 2521.898081] RTMP_TimerListAdd: add timer obj c84aade4!
[ 2521.898098] RTMP_TimerListAdd: add timer obj c84aae30!
[ 2521.898116] RTMP_TimerListAdd: add timer obj c84bb4b0!
[ 2521.898137] RTMP_TimerListAdd: add timer obj c84bb348!
[ 2521.898160] RTMP_TimerListAdd: add timer obj c84bb468!
[ 2521.902576] -->RTUSBVenderReset
[ 2521.902735] <--RTUSBVenderReset
[ 2522.384322] 1. Phy Mode = 5
[ 2522.384339] 2. Phy Mode = 5
[ 2522.384356] NVM is Efuse and its size =2d[2d0-2fc]
[ 2522.430536] phy mode> Error! The chip does not support 5G band 15!
[ 2522.431572] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 2522.436164] (Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc]
[ 2522.458000] 3. Phy Mode = 9
[ 2522.460872] AntCfgInit: primary/secondary ant 0/1
[ 2522.460882] AsicSetRxAnt, switch to main antenna
[ 2522.501828] MCS Set = ff 00 00 00 01
[ 2522.512559] <==== rt28xx_init, Status=0
[ 2522.514815] 0x1300 = 00064300
[ 2532.832061] ra0: no IPv6 routers present

Два модуля (rt2800usb и rt2870sta) запущены скорей всего потому что я сам подключал.
Собирал http://www.ralinktech.com/en/04_support/support.php?sn=501 как я понял это мне ничего не дало.

Код Выделить

/etc/hostapd/hostapd.conf

ctrl_interface=/var/run/hostapd
ctrl_interface_group=wheel
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=3
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP
wpa_passphrase=12345
driver=rt2800usb //пробовал и rt2870sta все равно не запускается
interface=ra0
hw_mode=n
channel=1
ssid=HOME_AP
country_code=RU
logger_syslog=-1
logger_syslog_level=1

Код Выделить

root@dhcppc1:~# service hostapd start
Starting advanced IEEE 802.11 management: hostapd failed!

dhcpd пока не крутил, все равно точка доступа не создается и не видна.
Поможете?

Русскоязычное сообщество Debian GNU/Linux

программная точка доступа Widemac SL-1507N

x3