Работа с жестким диском, удаление лишнего раздела!

[rayanAyar]

сами по себе они не создаются

Создаются. Расширенный раздел создает инсталлятор. Без него не создать логические диски.

Удаляйте старые разделы...

Не надо ничего делать. У автора абсолютно правильная разбивка. Никаких ошибок. Всё так и должно быть.

[yura_n]

Создаются. Расширенный раздел создает инсталлятор. Без него не создать логические диски.

Логические диски не обязательны, если разделов не более 4.

Никаких ошибок. Всё так и должно быть.

Автор темы написал, что выскакивает надпись о том, что диск используется с нештатными параметрами. А так быть не должно.

[rayanAyar]

выскакивает надпись о том, что диск используется с нештатными параметрами

Разбивка здесь не при чем. Это скорее всего смарт что-то нехорошее пытается сказать. Или какие-то параметры менялись софтом типа hdparm.

[yura_n]

Разбивка здесь не при чем. Это скорее всего смарт что-то нехорошее пытается сказать. Или какие-то параметры менялись софтом типа hdparm.

В любом случае начинать надо с бэкапа. А уже потом пытаться исправлять разделы. Иначе получится как всегда.

[PbI6A]

А ещё можно выложить (под spoiler!) вывод команды dmesg, а народ почитает и подумает.

[rayanAyar]

И смарт заодно.

[Babay]

А ещё можно выложить (под spoiler!) вывод команды dmesg, а народ почитает и подумает.

(Ничего себе! Вот это команда!)

Открыть содержимое (спойлер)

[159791.424135] sd 8:0:0:0: [sdb] 15654912 512-byte logical blocks: (8.01 GB/7.46 GiB)
[159791.425621] sd 8:0:0:0: [sdb] Write Protect is off
[159791.425628] sd 8:0:0:0: [sdb] Mode Sense: 23 00 00 00
[159791.425633] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[159791.429619] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[159791.429631]  sdb:
[159791.434618] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[159791.434629] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[159850.848377] usb 2-4: reset high speed USB device using ehci_hcd and address 2
[159869.544897] usb 2-4: USB disconnect, address 2
[159871.440052] usb 1-4: new high speed USB device using ehci_hcd and address 3
[159871.583165] usb 1-4: New USB device found, idVendor=13fe, idProduct=1f23
[159871.583174] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[159871.583181] usb 1-4: Product: -power
[159871.583185] usb 1-4: Manufacturer: silicon
[159871.583190] usb 1-4: SerialNumber: E6921A007A8F
[159871.583408] usb 1-4: configuration #1 chosen from 1 choice
[159871.583943] scsi9 : SCSI emulation for USB Mass Storage devices
[159871.584272] usb-storage: device found at 3
[159871.584276] usb-storage: waiting for device to settle before scanning
[159876.584597] usb-storage: device scan complete
[159876.586555] scsi 9:0:0:0: Direct-Access     silicon  -power           0.00 PQ: 0 ANSI: 0 CCS
[159876.587431] sd 9:0:0:0: Attached scsi generic sg2 type 0
[159876.855921] sd 9:0:0:0: [sdb] 15654912 512-byte logical blocks: (8.01 GB/7.46 GiB)
[159876.857408] sd 9:0:0:0: [sdb] Write Protect is off
[159876.857411] sd 9:0:0:0: [sdb] Mode Sense: 23 00 00 00
[159876.857414] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[159876.860410] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[159876.860415]  sdb:
[159876.864421] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[159876.864429] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[160259.988422] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[160259.988437] ata3.00: failed command: SMART
[160259.988453] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[160259.988456]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[160259.988463] ata3.00: status: { DRDY }
[160259.988475] ata3: hard resetting link
[160260.472066] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[160260.482413] ata3.00: configured for UDMA/133
[160260.482465] ata3: EH complete
[160439.438654] usb 1-4: USB disconnect, address 3
[162059.988423] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[162059.988436] ata3.00: failed command: SMART
[162059.988452] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[162059.988455]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[162059.988462] ata3.00: status: { DRDY }
[162059.988474] ata3: hard resetting link
[162060.472064] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[162060.482446] ata3.00: configured for UDMA/133
[162060.482501] ata3: EH complete
[162249.304051] usb 2-4: new high speed USB device using ehci_hcd and address 3
[162249.446104] usb 2-4: New USB device found, idVendor=13fe, idProduct=1f23
[162249.446114] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[162249.446120] usb 2-4: Product: -power
[162249.446124] usb 2-4: Manufacturer: silicon
[162249.446129] usb 2-4: SerialNumber: E6921A007A8F
[162249.446353] usb 2-4: configuration #1 chosen from 1 choice
[162249.446690] scsi10 : SCSI emulation for USB Mass Storage devices
[162249.446975] usb-storage: device found at 3
[162249.446979] usb-storage: waiting for device to settle before scanning
[162254.444345] usb-storage: device scan complete
[162254.446540] scsi 10:0:0:0: Direct-Access     silicon  -power           0.00 PQ: 0 ANSI: 0 CCS
[162254.447748] sd 10:0:0:0: Attached scsi generic sg2 type 0
[162254.715884] sd 10:0:0:0: [sdb] 15654912 512-byte logical blocks: (8.01 GB/7.46 GiB)
[162254.717376] sd 10:0:0:0: [sdb] Write Protect is off
[162254.717383] sd 10:0:0:0: [sdb] Mode Sense: 23 00 00 00
[162254.717388] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[162254.720382] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[162254.720391]  sdb:
[162254.723363] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[162254.723371] sd 10:0:0:0: [sdb] Attached SCSI removable disk
[162569.441433] usb 2-4: USB disconnect, address 3
[162575.832073] usb 2-4: new high speed USB device using ehci_hcd and address 4
[162575.974737] usb 2-4: New USB device found, idVendor=13fe, idProduct=1f23
[162575.974747] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[162575.974753] usb 2-4: Product: -power
[162575.974758] usb 2-4: Manufacturer: silicon
[162575.974762] usb 2-4: SerialNumber: E6921A007A8F
[162575.974991] usb 2-4: configuration #1 chosen from 1 choice
[162575.975323] scsi11 : SCSI emulation for USB Mass Storage devices
[162575.975580] usb-storage: device found at 4
[162575.975584] usb-storage: waiting for device to settle before scanning
[162580.972351] usb-storage: device scan complete
[162580.974172] scsi 11:0:0:0: Direct-Access     silicon  -power           0.00 PQ: 0 ANSI: 0 CCS
[162580.975363] sd 11:0:0:0: Attached scsi generic sg2 type 0
[162581.243526] sd 11:0:0:0: [sdb] 15654912 512-byte logical blocks: (8.01 GB/7.46 GiB)
[162581.245013] sd 11:0:0:0: [sdb] Write Protect is off
[162581.245020] sd 11:0:0:0: [sdb] Mode Sense: 23 00 00 00
[162581.245025] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[162581.247993] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[162581.248029]  sdb:
[162581.251995] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[162581.252039] sd 11:0:0:0: [sdb] Attached SCSI removable disk
[162581.822003] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[163859.988079] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[163859.988092] ata3.00: failed command: SMART
[163859.988108] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[163859.988111]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[163859.988118] ata3.00: status: { DRDY }
[163859.988131] ata3: hard resetting link
[163860.472048] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[163860.482184] ata3.00: configured for UDMA/133
[163860.482232] ata3: EH complete
[165659.988041] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[165659.988047] ata3.00: failed command: SMART
[165659.988055] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[165659.988056]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[165659.988059] ata3.00: status: { DRDY }
[165659.988065] ata3: hard resetting link
[165660.472056] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[165660.482514] ata3.00: configured for UDMA/133
[165660.482561] ata3: EH complete
[167459.988053] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[167459.988066] ata3.00: failed command: SMART
[167459.988082] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[167459.988085]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[167459.988092] ata3.00: status: { DRDY }
[167459.988103] ata3: hard resetting link
[167460.472033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[167460.482424] ata3.00: configured for UDMA/133
[167460.482453] ata3: EH complete
[169259.988049] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[169259.988062] ata3.00: failed command: SMART
[169259.988078] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[169259.988081]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[169259.988088] ata3.00: status: { DRDY }
[169259.988099] ata3: hard resetting link
[169260.472033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[169260.482412] ata3.00: configured for UDMA/133
[169260.482442] ata3: EH complete
[171059.988054] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[171059.988067] ata3.00: failed command: SMART
[171059.988083] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[171059.988086]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[171059.988093] ata3.00: status: { DRDY }
[171059.988104] ata3: hard resetting link
[171060.472033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[171060.482303] ata3.00: configured for UDMA/133
[171060.482332] ata3: EH complete
[172859.988076] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[172859.988091] ata3.00: failed command: SMART
[172859.988108] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[172859.988111]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[172859.988118] ata3.00: status: { DRDY }
[172859.988131] ata3: hard resetting link
[172860.472041] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[172860.482218] ata3.00: configured for UDMA/133
[172860.482264] ata3: EH complete
[174659.988383] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[174659.988397] ata3.00: failed command: SMART
[174659.988413] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[174659.988417]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[174659.988424] ata3.00: status: { DRDY }
[174659.988435] ata3: hard resetting link
[174660.472364] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[174660.482611] ata3.00: configured for UDMA/133
[174660.482644] ata3: EH complete
[176459.988063] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[176459.988078] ata3.00: failed command: SMART
[176459.988094] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[176459.988097]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[176459.988104] ata3.00: status: { DRDY }
[176459.988117] ata3: hard resetting link
[176460.472033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[176460.482135] ata3.00: configured for UDMA/133
[176460.482181] ata3: EH complete
[178259.988078] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[178259.988092] ata3.00: failed command: SMART
[178259.988108] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[178259.988111]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[178259.988118] ata3.00: status: { DRDY }
[178259.988130] ata3: hard resetting link
[178260.476053] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[178260.486528] ata3.00: configured for UDMA/133
[178260.486578] ata3: EH complete
[180059.988413] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[180059.988427] ata3.00: failed command: SMART
[180059.988443] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[180059.988446]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[180059.988454] ata3.00: status: { DRDY }
[180059.988466] ata3: hard resetting link
[180060.472402] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[180060.482661] ata3.00: configured for UDMA/133
[180060.482711] ata3: EH complete
[181859.988407] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[181859.988420] ata3.00: failed command: SMART
[181859.988436] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[181859.988440]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[181859.988447] ata3.00: status: { DRDY }
[181859.988459] ata3: hard resetting link
[181860.472042] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[181860.482402] ata3.00: configured for UDMA/133
[181860.482453] ata3: EH complete
[183659.988393] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[183659.988401] ata3.00: failed command: SMART
[183659.988410] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[183659.988412]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[183659.988416] ata3.00: status: { DRDY }
[183659.988424] ata3: hard resetting link
[183660.472385] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[183660.482750] ata3.00: configured for UDMA/133
[183660.482819] ata3: EH complete
[184479.903237] eth0: link down.
[184914.249295] eth0: link up.
[184921.793914] eth0: link down.
[184923.508195] eth0: link up.
[185459.988069] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[185459.988083] ata3.00: failed command: SMART
[185459.988099] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[185459.988102]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[185459.988109] ata3.00: status: { DRDY }
[185459.988122] ata3: hard resetting link
[185460.472043] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[185460.482423] ata3.00: configured for UDMA/133
[185460.482478] ata3: EH complete
[187259.988076] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[187259.988090] ata3.00: failed command: SMART
[187259.988106] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[187259.988109]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[187259.988117] ata3.00: status: { DRDY }
[187259.988129] ata3: hard resetting link
[187260.472053] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[187260.482446] ata3.00: configured for UDMA/133
[187260.482498] ata3: EH complete
[189059.988311] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[189059.988326] ata3.00: failed command: SMART
[189059.988342] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[189059.988345]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[189059.988353] ata3.00: status: { DRDY }
[189059.988365] ata3: hard resetting link
[189060.472044] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[189060.482096] ata3.00: configured for UDMA/133
[189060.482149] ata3: EH complete
[190859.988417] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[190859.988432] ata3.00: failed command: SMART
[190859.988447] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[190859.988451]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[190859.988458] ata3.00: status: { DRDY }
[190859.988470] ata3: hard resetting link
[190860.472379] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[190860.482757] ata3.00: configured for UDMA/133
[190860.482797] ata3: EH complete
[192659.988404] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[192659.988418] ata3.00: failed command: SMART
[192659.988434] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[192659.988437]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[192659.988444] ata3.00: status: { DRDY }
[192659.988457] ata3: hard resetting link
[192660.472042] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[192660.482317] ata3.00: configured for UDMA/133
[192660.482370] ata3: EH complete
[194459.988390] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[194459.988398] ata3.00: failed command: SMART
[194459.988407] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[194459.988409]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[194459.988413] ata3.00: status: { DRDY }
[194459.988421] ata3: hard resetting link
[194460.468382] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[194460.478704] ata3.00: configured for UDMA/133
[194460.478733] ata3: EH complete
[196259.988054] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[196259.988068] ata3.00: failed command: SMART
[196259.988084] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[196259.988088]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[196259.988095] ata3.00: status: { DRDY }
[196259.988105] ata3: hard resetting link
[196260.472033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[196260.482235] ata3.00: configured for UDMA/133
[196260.482262] ata3: EH complete
[198060.000065] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[198060.000078] ata3.00: failed command: SMART
[198060.000094] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[198060.000097]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[198060.000104] ata3.00: status: { DRDY }
[198060.000117] ata3: hard resetting link
[198060.484048] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[198060.494379] ata3.00: configured for UDMA/133
[198060.494414] ata3: EH complete
[199859.988048] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[199859.988062] ata3.00: failed command: SMART
[199859.988078] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[199859.988081]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[199859.988088] ata3.00: status: { DRDY }
[199859.988099] ata3: hard resetting link
[199860.472032] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[199860.482387] ata3.00: configured for UDMA/133
[199860.482417] ata3: EH complete
[201659.988071] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[201659.988084] ata3.00: failed command: SMART
[201659.988100] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[201659.988104]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[201659.988111] ata3.00: status: { DRDY }
[201659.988123] ata3: hard resetting link
[201660.472044] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[201660.482482] ata3.00: configured for UDMA/133
[201660.482528] ata3: EH complete
[203459.988077] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[203459.988091] ata3.00: failed command: SMART
[203459.988107] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[203459.988110]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[203459.988117] ata3.00: status: { DRDY }
[203459.988129] ata3: hard resetting link
[203460.472042] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[203460.482261] ata3.00: configured for UDMA/133
[203460.482307] ata3: EH complete
[205259.988085] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[205259.988099] ata3.00: failed command: SMART
[205259.988115] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[205259.988119]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[205259.988126] ata3.00: status: { DRDY }
[205259.988138] ata3: hard resetting link
[205260.472061] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[205260.482258] ata3.00: configured for UDMA/133
[205260.482305] ata3: EH complete
[207059.988062] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[207059.988076] ata3.00: failed command: SMART
[207059.988092] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[207059.988096]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[207059.988103] ata3.00: status: { DRDY }
[207059.988115] ata3: hard resetting link
[207060.472035] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[207060.482198] ata3.00: configured for UDMA/133
[207060.482236] ata3: EH complete
[208859.988083] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[208859.988098] ata3.00: failed command: SMART
[208859.988115] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[208859.988118]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[208859.988125] ata3.00: status: { DRDY }
[208859.988138] ata3: hard resetting link
[208860.472033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[208860.482542] ata3.00: configured for UDMA/133
[208860.482588] ata3: EH complete
[210659.988085] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[210659.988099] ata3.00: failed command: SMART
[210659.988115] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[210659.988118]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[210659.988126] ata3.00: status: { DRDY }
[210659.988138] ata3: hard resetting link
[210660.472058] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[210660.482275] ata3.00: configured for UDMA/133
[210660.482321] ata3: EH complete
[212460.000102] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[212460.000116] ata3.00: failed command: SMART
[212460.000132] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[212460.000135]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[212460.000142] ata3.00: status: { DRDY }
[212460.000155] ata3: hard resetting link
[212460.484049] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[212460.494343] ata3.00: configured for UDMA/133
[212460.494394] ata3: EH complete
[214259.988080] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[214259.988094] ata3.00: failed command: SMART
[214259.988110] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[214259.988113]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[214259.988120] ata3.00: status: { DRDY }
[214259.988133] ata3: hard resetting link
[214260.472039] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[214260.482277] ata3.00: configured for UDMA/133
[214260.482324] ata3: EH complete
[216059.988086] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[216059.988101] ata3.00: failed command: SMART
[216059.988117] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[216059.988120]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[216059.988127] ata3.00: status: { DRDY }
[216059.988140] ata3: hard resetting link
[216060.472039] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[216060.482324] ata3.00: configured for UDMA/133
[216060.482375] ata3: EH complete
[217859.988075] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[217859.988090] ata3.00: failed command: SMART
[217859.988106] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[217859.988109]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[217859.988117] ata3.00: status: { DRDY }
[217859.988129] ata3: hard resetting link
[217860.472047] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[217860.482420] ata3.00: configured for UDMA/133
[217860.482466] ata3: EH complete
[219659.988395] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[219659.988409] ata3.00: failed command: SMART
[219659.988425] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[219659.988429]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[219659.988436] ata3.00: status: { DRDY }
[219659.988448] ata3: hard resetting link
[219660.472370] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[219660.482772] ata3.00: configured for UDMA/133
[219660.482819] ata3: EH complete
[221459.988402] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[221459.988416] ata3.00: failed command: SMART
[221459.988431] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[221459.988435]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[221459.988442] ata3.00: status: { DRDY }
[221459.988454] ata3: hard resetting link
[221460.472075] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[221460.482472] ata3.00: configured for UDMA/133
[221460.482523] ata3: EH complete
[223259.988079] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[223259.988093] ata3.00: failed command: SMART
[223259.988109] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[223259.988113]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[223259.988120] ata3.00: status: { DRDY }
[223259.988132] ata3: hard resetting link
[223260.472068] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[223260.482425] ata3.00: configured for UDMA/133
[223260.482475] ata3: EH complete
[225059.988070] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[225059.988084] ata3.00: failed command: SMART
[225059.988100] ata3.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[225059.988103]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[225059.988110] ata3.00: status: { DRDY }
[225059.988122] ata3: hard resetting link
[225060.472039] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[225060.482678] ata3.00: configured for UDMA/133
[225060.482727] ata3: EH complete
[226239.988071] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[226239.988084] ata3.00: failed command: SMART
[226239.988100] ata3.00: cmd b0/d5:01:01:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[226239.988103]          res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[226239.988112] ata3.00: status: { DRDY }
[226239.988126] ata3: hard resetting link
[226240.472374] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[226240.482630] ata3.00: configured for UDMA/133
[226240.482679] ata3: EH complete
[226635.102688] usb 2-4: USB disconnect, address 4
al@deb:~$

[свернуть]

И смарт заодно.

А вот и мой смарт (Это???)

Открыть содержимое (спойлер)

al@deb:~$ sudo smartctl -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint S250 series
Device Model:     SAMSUNG HD250HJ
Serial Number:    S0URJDWQ204950
Firmware Version: FH100-06
User Capacity:    250 059 350 016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 3b
Local Time is:    Mon Nov 26 08:56:16 2012 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

Error SMART Values Read failed: Ошибка ввода/вывода
Smartctl: SMART Read Values failed.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.

Error SMART Error Log Read failed: Ошибка ввода/вывода
Smartctl: SMART Error Log Read Failed
Error SMART Error Self-Test Log Read failed: Ошибка ввода/вывода
Smartctl: SMART Self Test Log Read Failed
Device does not support Selective Self Tests/Logging
al@deb:~$

[свернуть]

(Для меня все это - как "китайская грамота"! )
Надеюсь....очень надеюсь!

[qupl]

Да, со смартом ошибка.На одной матери я в BIOS Setup видел настройку, что-то вроде "поддержка SMART", не мешало бы посмотреть на ее наличие.
Зато теперь точно видно, что диск на 250 Гб

[rayanAyar]

[160259.988437] ata3.00: failed command: SMART
Error SMART Values Read failed:

Это кстати и может быть причиной надписи о том, что

диск используется с нештатными параметрами

Т.е. на самом деле система не знает (так как не может прочитать по каким-то причинам) с какими параметрами "используется диск". И поэтому выдает такое предупреждение.

[PbI6A]

Странные заморочки со SMART, надо бы с ними разобраться. Посмотреть, включен ли SMART в BIOS, включить, да и протестировать бы поверхность винта. Часто проблемы со SMART бывают признаком надвигающейся его (винта) смерти

[Babay]

Странные заморочки со SMART, надо бы с ними разобраться. Посмотреть, включен ли SMART в BIOS, включить, да и протестировать бы поверхность винта.

Не подскажите, как это сделать - что там да как?
В БИОС забраться я могу, а вот дальше... Боюсь напортачить там...

[qupl]

Как-то так.

[PbI6A]

Я обычно тестирование поверхности делаю с помощью MHDD. Она под DOS и под оффтопик, там есть даже какой-то загрузочный iso. Но я его (пока) не смотрел.

[qupl]

Пользуюсь MHDD загрузочным, но там ограничения есть. IDE диск надо только как master подключать.

[Babay]

Как-то так.

Я обычно тестирование поверхности делаю с помощью MHDD. Она под DOS и под оффтопик, там есть даже какой-то загрузочный iso. Но я его (пока) не смотрел.

Класс!!!
Пока только взглянул, но на первый взгляд - для меня самое то! Вечером, после работы буду читать и делать!
Спасибо!!!