[Решено] Не монтируется флешка

[noname]

В консоли dmesg и cat /var/log/messages

[http]

В консоли dmesg и cat /var/log/messages

вот кароче че там
Jun 24 01:31:46 localhost kernel: [213455.356606]  sdb:
Jun 24 01:31:46 localhost kernel: [213455.363656] sd 11:0:0:0: [sdb]
Attached SCSI removable disk

[noname]

честно хз почему fdisk не видит, а gparted установлен если да то запусти посмотри

[http]

честно хз почему fdisk не видит, а gparted установлен если да то запусти посмотри

ОК, щас
Сообщение объединено: 24 июня 2013, 01:57:44

честно хз почему fdisk не видит, а gparted установлен если да то запусти посмотри

нет не видит ладно завтра создам раздел там в флешке

[noname]

вывод lsmod  | grep usb
может модули не подгружены

[http]

вывод lsmod  | grep usb
может модули не подгружены

Код Выделить Развернуть

[    1.187144] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.187149] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.187296] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.188993] sr1: scsi3-mmc drive: 39x/94x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.189127] sr 3:0:1:0: Attached scsi CD-ROM sr1
[    1.206146]  sda: sda1 sda2 sda3
[    1.206463] sd 2:0:0:0: [sda] Attached SCSI disk
[    1.208036] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.208071] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    1.208102] sr 3:0:1:0: Attached scsi generic sg2 type 5
[    1.244332] hub 1-0:1.0: unable to enumerate USB device on port 1
[    1.432339] hub 1-0:1.0: unable to enumerate USB device on port 1
[    1.496014] Refined TSC clocksource calibration: 2933.333 MHz.
[    1.496020] Switching to clocksource tsc
[    1.620329] hub 1-0:1.0: unable to enumerate USB device on port 1
[    1.864018] usb 1-1: new high-speed USB device number 5 using ehci_hcd
[    1.932189] hub 1-0:1.0: unable to enumerate USB device on port 1
[    2.376011] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[    2.524436] usb 2-1: not running at top speed; connect to a high speed hub
[    2.680437] usb 2-1: New USB device found, idVendor=046d, idProduct=0826
[    2.680441] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=1
[    2.680444] usb 2-1: Product: HD Webcam C525
[    2.680447] usb 2-1: SerialNumber: 1CCEAED0
[    4.501636] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07
[    4.503445] platform microcode: firmware: agent loaded intel-ucode/06-17-0a into memory
[    4.507421] microcode: CPU0 updated to revision 0xa0b, date = 2010-09-28
[    4.507882] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07
[    4.509693] platform microcode: firmware: agent loaded intel-ucode/06-17-0a into memory
[    4.513667] microcode: CPU1 updated to revision 0xa0b, date = 2010-09-28
[    4.514174] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    4.614885] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    6.011465] udevd[354]: starting version 175
[    6.362057] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    6.362062] ACPI: Power Button [PWRB]
[    6.362119] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    6.362121] ACPI: Power Button [PWRF]
[    6.479665] intel_rng: FWH not detected
[    6.497973] iTCO_vendor_support: vendor-support=0
[    6.499116] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    6.499195] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[    6.499571] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    6.563839] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[    6.563861] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[    6.581572] parport_pc 00:09: reported by Plug and Play ACPI
[    6.581590] input: PC Speaker as /devices/platform/pcspkr/input/input3
[    6.581626] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[    6.593197] leds_ss4200: no LED devices found
[    6.598183] ACPI: Requesting acpi_cpufreq
[    6.619985] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
[    6.966168] [drm] Initialized drm 1.1.0 20060810
[    6.968922] Linux media interface: v0.10
[    6.979178] Linux video capture interface: v2.00
[    7.117543] i915 0000:00:02.0: setting latency timer to 64
[    7.128951] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
[    7.128953] [drm] MTRR allocation failed.  Graphics performance may suffer.
[    7.129124] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[    7.129128] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    7.129129] [drm] Driver supports precise vblank timestamp query.
[    7.129159] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    7.138551] [drm] initialized overlay support
[    7.185448] fbcon: inteldrmfb (fb0) is primary device
[    7.189817] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[    7.189869] saa7133[0]: found at 0000:03:00.0, rev: 209, irq: 20, latency: 32, mmio: 0xfdbff000
[    7.189874] saa7133[0]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid [card=112,autodetected]
[    7.189885] saa7133[0]: board init: gpio is 0
[    7.228150] IR NEC protocol handler initialized
[    7.230325] Console: switching to colour frame buffer device 210x65
[    7.235922] fb0: inteldrmfb frame buffer device
[    7.235923] drm: registered panic notifier
[    7.235963] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    7.244010] Registered IR keymap rc-asus-pc39
[    7.244127] input: saa7134 IR (ASUSTeK P7131 Hybri as /devices/pci0000:00/0000:00:1e.0/0000:03:00.0/rc/rc0/input5
[    7.244191] rc0: saa7134 IR (ASUSTeK P7131 Hybri as /devices/pci0000:00/0000:00:1e.0/0000:03:00.0/rc/rc0
[    7.314279] IR RC5(x) protocol handler initialized
[    7.331976] IR RC6 protocol handler initialized
[    7.375545] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input6
[    7.396013] saa7133[0]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[    7.396026] saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff
[    7.396037] saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff ff
[    7.396048] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396059] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff ff
[    7.396070] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396081] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396092] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396103] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396114] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396125] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396136] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396147] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396158] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396169] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.396186] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    7.442158] IR JVC protocol handler initialized
[    7.608036] i2c-core: driver [tuner] using legacy suspend method
[    7.608038] i2c-core: driver [tuner] using legacy resume method
[    7.693700] IR Sony protocol handler initialized
[    7.738968] uvcvideo: Found UVC 1.00 device HD Webcam C525 (046d:0826)
[    7.752566] input: HD Webcam C525 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.2/input/input7
[    7.752647] usbcore: registered new interface driver uvcvideo
[    7.752648] USB Video Class driver (1.1.1)
[    7.799758] input: MCE IR Keyboard/Mouse (saa7134) as /devices/virtual/input/input8
[    7.799820] IR MCE Keyboard/mouse protocol handler initialized
[    7.840027] tuner 9-004b: Tuner -1 found with type(s) Radio TV.
[    7.891773] lirc_dev: IR Remote Control driver registered, major 251
[    7.892250] rc rc0: lirc_dev: driver ir-lirc-codec (saa7134) registered at minor = 0
[    7.892252] IR LIRC bridge handler initialized
[    7.920012] tda829x 9-004b: setting tuner address to 61
[    7.954639] usbcore: registered new interface driver snd-usb-audio
[    8.008068] tda829x 9-004b: type set to tda8290+75a
[   10.576207] saa7133[0]: dsp access error
[   10.576210] saa7133[0]: dsp access error
[   10.576251] saa7133[0]: dsp access error
[   10.640088] saa7133[0]: registered device video1 [v4l2]
[   10.640192] saa7133[0]: registered device vbi0
[   10.640257] saa7133[0]: registered device radio0
[   10.686609] dvb_init() allocating 1 frontend
[   10.720012] DVB: registering new adapter (saa7133[0])
[   10.720017] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[   10.928009] tda1004x: setting up plls for 48MHz sampling clock
[   13.290692] Adding 4300796k swap on /dev/sda2.  Priority:-1 extents:1 across:4300796k
[   13.307509] EXT4-fs (sda1): re-mounted. Opts: (null)
[   13.348015] tda1004x: timeout waiting for DSP ready
[   13.388007] tda1004x: found firmware revision 0 -- invalid
[   13.388010] tda1004x: trying to boot from eeprom
[   13.587177] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   13.684788] fuse init (API version 7.17)
[   13.722302] [997]: VMCI: shared components initialized.
[   13.722354] [997]: VMCI: host components initialized.
[   13.722518] [997]: VMCI: Module registered (name=vmci,major=10,minor=59).
[   13.722522] [997]: VMCI: Using host personality
[   13.722525] [997]: VMCI: Module (name=vmci) is initialized
[   14.317558] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[   15.058890] RPC: Registered named UNIX socket transport module.
[   15.058895] RPC: Registered udp transport module.
[   15.058897] RPC: Registered tcp transport module.
[   15.058900] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   15.100297] FS-Cache: Loaded
[   15.123162] FS-Cache: Netfs 'nfs' registered for caching
[   15.137707] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   15.716006] tda1004x: timeout waiting for DSP ready
[   15.756047] tda1004x: found firmware revision 0 -- invalid
[   15.756051] tda1004x: waiting for firmware upload...
[   15.819895] saa7134 0000:03:00.0: firmware: agent aborted loading dvb-fe-tda10046.fw (not found?)
[   15.822649] saa7134 0000:03:00.0: firmware: agent aborted loading dvb-fe-tda10045.fw (not found?)
[   15.822864] tda1004x: firmware upload failed
[   16.094637] saa7134 ALSA driver for DMA sound loaded
[   16.094677] saa7133[0]/alsa: saa7133[0] at 0xfdbff000 irq 20 registered as card -1
[   17.110266] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input9
[   17.755627] Bluetooth: Core ver 2.16
[   17.755646] NET: Registered protocol family 31
[   17.755648] Bluetooth: HCI device and connection manager initialized
[   17.755650] Bluetooth: HCI socket layer initialized
[   17.755652] Bluetooth: L2CAP socket layer initialized
[   17.755657] Bluetooth: SCO socket layer initialized
[   17.782514] Bluetooth: RFCOMM TTY layer initialized
[   17.782519] Bluetooth: RFCOMM socket layer initialized
[   17.782521] Bluetooth: RFCOMM ver 1.11
[   17.832168] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.832171] Bluetooth: BNEP filters: protocol multicast
[   17.869031] lp0: using parport0 (interrupt-driven).
[   18.001837] ppdev: user-space parallel port driver
[   21.155335] atl1c 0000:02:00.0: irq 44 for MSI/MSI-X
[   21.155428] atl1c 0000:02:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[   21.873214] vboxdrv: Found 2 processor cores.
[   21.873318] vboxdrv: fAsync=0 offMin=0x1b8 offMax=0x7fe
[   21.873364] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   21.873365] vboxdrv: Successfully loaded version 4.2.12 (interface 0x001a0004).
[   22.197661] vboxpci: IOMMU not found (not compiled)
[   31.752010] eth0: no IPv6 routers present
[   46.144412] ISO 9660 Extensions: Microsoft Joliet Level 3
[   47.236725] ISO 9660 Extensions: RRIP_1991A
[  165.157533] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[32919.595617] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[32963.336831] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[198010.690447] EXT4-fs (sda3): Unaligned AIO/DIO on inode 6553748 by AioMgr0-N; performance will be poor.
[204202.024030] usb 1-2: new high-speed USB device number 6 using ehci_hcd
[204202.158571] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[204202.158577] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[204202.158580] usb 1-2: Product: DT 101 G2
[204202.158583] usb 1-2: Manufacturer: Kingston
[204202.158586] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[204202.911407] Initializing USB Mass Storage driver...
[204202.911543] scsi4 : usb-storage 1-2:1.0
[204202.911612] usbcore: registered new interface driver usb-storage
[204202.911614] USB Mass Storage support registered.
[204203.970653] scsi 4:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[204203.971529] sd 4:0:0:0: Attached scsi generic sg3 type 0
[204203.974483] sd 4:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[204203.974851] sd 4:0:0:0: [sdb] Write Protect is off
[204203.974854] sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[204203.975354] sd 4:0:0:0: [sdb] No Caching mode page present
[204203.975357] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[204203.978351] sd 4:0:0:0: [sdb] No Caching mode page present
[204203.978355] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[204203.979000]  sdb:
[204203.982621] sd 4:0:0:0: [sdb] No Caching mode page present
[204203.982626] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[204203.982629] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[204659.552701] end_request: I/O error, dev fd0, sector 0
[204671.724787] end_request: I/O error, dev fd0, sector 0
[204671.724793] Buffer I/O error on device fd0, logical block 0
[204683.892359] end_request: I/O error, dev fd0, sector 0
[204683.892364] Buffer I/O error on device fd0, logical block 0
[204696.064737] end_request: I/O error, dev fd0, sector 0
[204696.064743] Buffer I/O error on device fd0, logical block 0
[204708.232580] end_request: I/O error, dev fd0, sector 0
[204708.232585] Buffer I/O error on device fd0, logical block 0
[204720.388618] end_request: I/O error, dev fd0, sector 0
[204720.388623] Buffer I/O error on device fd0, logical block 0
[204732.552418] end_request: I/O error, dev fd0, sector 0
[204732.552424] Buffer I/O error on device fd0, logical block 0
[204744.720566] end_request: I/O error, dev fd0, sector 0
[204744.720571] Buffer I/O error on device fd0, logical block 0
[204756.872807] end_request: I/O error, dev fd0, sector 0
[204756.872814] Buffer I/O error on device fd0, logical block 0
[204769.044772] end_request: I/O error, dev fd0, sector 0
[204769.044778] Buffer I/O error on device fd0, logical block 0
[204781.212990] end_request: I/O error, dev fd0, sector 0
[204781.212997] Buffer I/O error on device fd0, logical block 0
[204793.376520] end_request: I/O error, dev fd0, sector 0
[204793.376527] Buffer I/O error on device fd0, logical block 0
[204805.536811] end_request: I/O error, dev fd0, sector 0
[204805.536817] Buffer I/O error on device fd0, logical block 0
[204817.704846] end_request: I/O error, dev fd0, sector 0
[204817.704853] Buffer I/O error on device fd0, logical block 0
[204829.872841] end_request: I/O error, dev fd0, sector 0
[204829.872848] Buffer I/O error on device fd0, logical block 0
[204842.040727] end_request: I/O error, dev fd0, sector 0
[204842.040735] Buffer I/O error on device fd0, logical block 0
[204854.208606] end_request: I/O error, dev fd0, sector 0
[204854.208612] Buffer I/O error on device fd0, logical block 0
[204866.372555] end_request: I/O error, dev fd0, sector 0
[204877.307437] usb 1-2: USB disconnect, device number 6
[204878.532835] end_request: I/O error, dev fd0, sector 0
[204878.532843] Buffer I/O error on device fd0, logical block 0
[204879.109686] usb 1-2: new high-speed USB device number 7 using ehci_hcd
[204879.242817] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[204879.242821] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[204879.242823] usb 1-2: Product: DT 101 G2
[204879.242824] usb 1-2: Manufacturer: Kingston
[204879.242826] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[204879.243416] scsi5 : usb-storage 1-2:1.0
[204880.302553] scsi 5:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[204880.303212] sd 5:0:0:0: Attached scsi generic sg3 type 0
[204880.303836] sd 5:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[204880.304335] sd 5:0:0:0: [sdb] Write Protect is off
[204880.304337] sd 5:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[204880.305055] sd 5:0:0:0: [sdb] No Caching mode page present
[204880.305059] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[204880.307518] sd 5:0:0:0: [sdb] No Caching mode page present
[204880.307521] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[204880.308155]  sdb:
[204880.312340] sd 5:0:0:0: [sdb] No Caching mode page present
[204880.312344] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[204880.312346] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[204890.704472] end_request: I/O error, dev fd0, sector 0
[204890.704478] Buffer I/O error on device fd0, logical block 0
[204895.788859] usb 1-2: USB disconnect, device number 7
[204898.404031] usb 1-2: new high-speed USB device number 8 using ehci_hcd
[204898.538685] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[204898.538690] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[204898.538693] usb 1-2: Product: DT 101 G2
[204898.538696] usb 1-2: Manufacturer: Kingston
[204898.538699] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[204898.539144] scsi6 : usb-storage 1-2:1.0
[204899.598738] scsi 6:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[204899.599825] sd 6:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[204899.599968] sd 6:0:0:0: Attached scsi generic sg3 type 0
[204899.600329] sd 6:0:0:0: [sdb] Write Protect is off
[204899.600331] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[204899.600821] sd 6:0:0:0: [sdb] No Caching mode page present
[204899.600824] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[204899.604581] sd 6:0:0:0: [sdb] No Caching mode page present
[204899.604586] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[204899.605226]  sdb:
[204899.609898] sd 6:0:0:0: [sdb] No Caching mode page present
[204899.609903] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[204899.609906] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[204902.860449] end_request: I/O error, dev fd0, sector 0
[204902.860456] Buffer I/O error on device fd0, logical block 0
[204915.032694] end_request: I/O error, dev fd0, sector 0
[204915.032700] Buffer I/O error on device fd0, logical block 0
[204927.196592] end_request: I/O error, dev fd0, sector 0
[204939.368548] end_request: I/O error, dev fd0, sector 0
[204939.368553] Buffer I/O error on device fd0, logical block 0
[204951.532834] end_request: I/O error, dev fd0, sector 0
[204951.532840] Buffer I/O error on device fd0, logical block 0
[204963.696551] end_request: I/O error, dev fd0, sector 0
[204963.696557] Buffer I/O error on device fd0, logical block 0
[204975.856603] end_request: I/O error, dev fd0, sector 0
[204975.856608] Buffer I/O error on device fd0, logical block 0
[204988.021641] end_request: I/O error, dev fd0, sector 0
[204988.021647] Buffer I/O error on device fd0, logical block 0
[205000.180484] end_request: I/O error, dev fd0, sector 0
[205000.180490] Buffer I/O error on device fd0, logical block 0
[205012.348643] end_request: I/O error, dev fd0, sector 0
[205012.348649] Buffer I/O error on device fd0, logical block 0
[205024.513182] end_request: I/O error, dev fd0, sector 0
[205024.513189] Buffer I/O error on device fd0, logical block 0
[205036.672337] end_request: I/O error, dev fd0, sector 0
[205036.672345] Buffer I/O error on device fd0, logical block 0
[205048.840597] end_request: I/O error, dev fd0, sector 0
[205048.840602] Buffer I/O error on device fd0, logical block 0
[205061.004474] end_request: I/O error, dev fd0, sector 0
[205061.004479] Buffer I/O error on device fd0, logical block 0
[205064.499729] EXT4-fs (sdb): VFS: Can't find ext4 filesystem
[205064.577230] ISOFS: Unable to identify CD-ROM format.
[205073.168609] end_request: I/O error, dev fd0, sector 0
[205073.168617] Buffer I/O error on device fd0, logical block 0
[205085.332785] end_request: I/O error, dev fd0, sector 0
[205085.332791] Buffer I/O error on device fd0, logical block 0
[205097.496602] end_request: I/O error, dev fd0, sector 0
[205097.496609] Buffer I/O error on device fd0, logical block 0
[205109.664640] end_request: I/O error, dev fd0, sector 0
[205109.664648] Buffer I/O error on device fd0, logical block 0
[205121.832379] end_request: I/O error, dev fd0, sector 0
[205121.832385] Buffer I/O error on device fd0, logical block 0
[205133.996743] end_request: I/O error, dev fd0, sector 0
[205133.996751] Buffer I/O error on device fd0, logical block 0
[205146.160603] end_request: I/O error, dev fd0, sector 0
[205146.160611] Buffer I/O error on device fd0, logical block 0
[205158.320848] end_request: I/O error, dev fd0, sector 0
[205158.320854] Buffer I/O error on device fd0, logical block 0
[205170.496320] end_request: I/O error, dev fd0, sector 0
[205170.496327] Buffer I/O error on device fd0, logical block 0
[205182.648631] end_request: I/O error, dev fd0, sector 0
[205182.648637] Buffer I/O error on device fd0, logical block 0
[205194.808324] end_request: I/O error, dev fd0, sector 0
[205194.808331] Buffer I/O error on device fd0, logical block 0
[205206.960402] end_request: I/O error, dev fd0, sector 0
[205206.960408] Buffer I/O error on device fd0, logical block 0
[205219.128580] end_request: I/O error, dev fd0, sector 0
[205219.128586] Buffer I/O error on device fd0, logical block 0
[205231.292351] end_request: I/O error, dev fd0, sector 0
[205231.292357] Buffer I/O error on device fd0, logical block 0
[205312.064234] usb 1-2: USB disconnect, device number 8
[205314.860032] usb 1-2: new high-speed USB device number 9 using ehci_hcd
[205314.994975] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[205314.994980] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[205314.994984] usb 1-2: Product: DT 101 G2
[205314.994986] usb 1-2: Manufacturer: Kingston
[205314.994989] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[205314.995386] scsi7 : usb-storage 1-2:1.0
[205316.054660] scsi 7:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[205316.055573] sd 7:0:0:0: Attached scsi generic sg3 type 0
[205316.056642] sd 7:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[205316.057126] sd 7:0:0:0: [sdb] Write Protect is off
[205316.057130] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[205316.057523] sd 7:0:0:0: [sdb] No Caching mode page present
[205316.057527] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[205316.062499] sd 7:0:0:0: [sdb] No Caching mode page present
[205316.062505] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[205316.063156]  sdb:
[205316.069685] sd 7:0:0:0: [sdb] No Caching mode page present
[205316.069691] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[205316.069695] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[205432.760405] usb 1-2: USB disconnect, device number 9
[205433.932033] usb 1-2: new high-speed USB device number 10 using ehci_hcd
[205434.066764] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[205434.066770] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[205434.066773] usb 1-2: Product: DT 101 G2
[205434.066776] usb 1-2: Manufacturer: Kingston
[205434.066778] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[205434.073518] scsi8 : usb-storage 1-2:1.0
[205435.135286] scsi 8:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[205435.137591] sd 8:0:0:0: Attached scsi generic sg3 type 0
[205435.138043] sd 8:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[205435.138430] sd 8:0:0:0: [sdb] Write Protect is off
[205435.138433] sd 8:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[205435.138915] sd 8:0:0:0: [sdb] No Caching mode page present
[205435.138920] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[205435.143033] sd 8:0:0:0: [sdb] No Caching mode page present
[205435.143039] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[205435.143981]  sdb:
[205435.146044] sd 8:0:0:0: [sdb] No Caching mode page present
[205435.146051] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[205435.146055] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[205440.297641] usb 1-2: USB disconnect, device number 10
[205468.156028] usb 1-2: new high-speed USB device number 11 using ehci_hcd
[205468.290790] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[205468.290795] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[205468.290799] usb 1-2: Product: DT 101 G2
[205468.290802] usb 1-2: Manufacturer: Kingston
[205468.290804] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[205468.293199] scsi9 : usb-storage 1-2:1.0
[205469.355595] scsi 9:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[205469.357885] sd 9:0:0:0: Attached scsi generic sg3 type 0
[205469.358193] sd 9:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[205469.359070] sd 9:0:0:0: [sdb] Write Protect is off
[205469.359075] sd 9:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[205469.359554] sd 9:0:0:0: [sdb] No Caching mode page present
[205469.359558] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[205469.363180] sd 9:0:0:0: [sdb] No Caching mode page present
[205469.363185] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[205469.364026]  sdb:
[205469.366579] sd 9:0:0:0: [sdb] No Caching mode page present
[205469.366584] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[205469.366588] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[205492.880288] end_request: I/O error, dev fd0, sector 0
[207484.205457] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[207484.205944] FAT-fs (sdb): invalid media value (0x00)
[207484.205949] FAT-fs (sdb): Can't find a valid FAT filesystem
[207664.624477] end_request: I/O error, dev fd0, sector 0
[213088.387651] usb 1-2: USB disconnect, device number 11
[213090.340047] usb 1-2: new high-speed USB device number 12 using ehci_hcd
[213090.474654] usb 1-2: New USB device found, idVendor=0951, idProduct=1642
[213090.474659] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[213090.474663] usb 1-2: Product: DT 101 G2
[213090.474665] usb 1-2: Manufacturer: Kingston
[213090.474668] usb 1-2: SerialNumber: 001CC07CEE5EFBA0791B2461
[213090.478226] scsi10 : usb-storage 1-2:1.0
[213091.538706] scsi 10:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 0 CCS
[213091.539878] sd 10:0:0:0: Attached scsi generic sg3 type 0
[213091.540303] sd 10:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[213091.540802] sd 10:0:0:0: [sdb] Write Protect is off
[213091.540806] sd 10:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[213091.541233] sd 10:0:0:0: [sdb] No Caching mode page present
[213091.541237] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[213091.545222] sd 10:0:0:0: [sdb] No Caching mode page present
[213091.545227] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[213091.545825]  sdb:
[213091.547641] sd 10:0:0:0: [sdb] No Caching mode page present
[213091.547646] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[213091.547650] sd 10:0:0:0: [sdb] Attached SCSI removable disk
root@localhost:/# lsmod  | grep usb
usb_storage            35142  0
snd_usb_audio          71309  2
snd_usbmidi_lib        18801  1 snd_usb_audio
snd_rawmidi            22472  2 snd_seq_midi,snd_usbmidi_lib
snd_hwdep              12943  2 snd_hda_codec,snd_usb_audio
snd_pcm                53461  6 snd_hda_codec,snd_hda_intel,snd_usb_audio,saa7134_alsa
snd                    42722  24 snd_timer,snd_seq_device,snd_seq,snd_pcm,snd_hwdep,snd_hda_codec,snd_hda_intel,snd_hda_codec_realtek,snd_rawmidi,snd_usbmidi_lib,snd_usb_audio,saa7134_alsa
scsi_mod              135037  5 libata,sd_mod,sr_mod,sg,usb_storage
usbcore               104555  7 ehci_hcd,uhci_hcd,uvcvideo,snd_usbmidi_lib,snd_usb_audio,usb_storage
usb_common             12338  1 usbcore
root@localhost:/# lsmod  | grep usb /home/less.txt
grep: /home/less.txt: Нет такого файла или каталога
root@localhost:/#

*устное предупреждение: прочитайте правила форума, вывод команд, занимающих больше половины экрана лучше убирать под теги spoiler или code. qupl

[noname]

и попробуй modprobe vfat от root

[http]

modprobe vfat

и попробуй modprobe vfat от root

нет завтра кароче создам раздел и расскажу че да как)))

[noname]

у тебя наверно модуль не загружен vfat
lsmod | grep vfat если нет ничего то modprobe vfat и передерни флеху и fdisk смотри
Да и длинные выводы лучше под спойлер прятать

[http]

lsmod | grep vfat

Диск /dev/sdb: 4009 МБ, 4009754624 байт
124 heads, 62 sectors/track, 1018 cylinders, всего 7831552 секторов
Units = секторы of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x194907a2
один хрен кароче завтра разберусь

[noname]

На своей флешке Transcend 4gb jf-v10(FAT32) cпецом удалил  разделы и теперь вывод fdisk -l такойже как у тебя

Открыть содержимое (спойлер)

~ # fdisk -l
Disk /dev/sdb: 4016 MB, 4016046080 bytes
124 heads, 62 sectors/track, 1020 cylinders, total 7843840 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0005fe32

   Device Boot      Start         End      Blocks   Id  System

[свернуть]

Вывод как бы намекает нам,отсутствует таблица разделов

Открыть содержимое (спойлер)

Если не лень проверь еще раз флешку на работоспособность в window$,если определится скопируй данные и форматни,не выйдет тогда или форматируй тем же gparted или восстанавливать данные

[свернуть]

Может быть ты случайно потер еЁ,такое тоже возможно.

[http]

   Device Boot      Start         End      Blocks   Id  System[/spoiler]Вывод как бы намекает нам,отсутствует таблица разделов

Открыть содержимое (спойлер)

Если не лень проверь еще раз флешку на работоспособность в window$,если определится скопируй данные и форматни,не выйдет тогда или форматируй тем же gparted или восстанавливать данные

[свернуть]

Может быть ты случайно потер еЁ,такое тоже возможно.

ну че кароче все я зделал просто по новой разметил флешку. и отформотировал терь все работает , дело было в номере раздела линукс реально не видил че ето такое, потом правда када подключил все она сразу определилась. но не открывалась и я через терминал ее примонтировал в папку /flash терь все работает. спс те что помог разобраться)) да кстати ешо, как закрыть тему?

[qupl]

да кстати ешо, как закрыть тему?

Иправить первое сообщение темы, добавить [Решено] , потом нажать кнопку "заблокировать тему" внизу страницы.

[http]

Иправить первое сообщение темы, добавить [Решено] , потом нажать кнопку "заблокировать тему" внизу страницы.

cgc