Автор Тема: Dell 610 wi fi  (Прочитано 4376 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Оффлайн mtc93rus

Dell 610 wi fi
« : 26 Июня 2015, 00:55:41 »
Всем привет.
Решил попробовать дистр дебиан(ранее пользовался убунтой и ее производными). Возникла проблема с карточкой wi fi( в интернете не нашел годного решения для дебиан). Значит ноутбук dell 610, карточка broadcom bcm4318. В убунте решалось тем, что я убирал из черного листа bcm43xx
sudo gedit /etc/modprobe.d/blacklist.conf
затем доставлял пакеты
b43-fwcutter   firmware-b43-installer
 и все работало(так же это действовало на убунтоподобных системах). Тут же так не получилось.

Есть ли идеи как исправить?
 

Оффлайн ChubaDuba

Re: Dell 610 wi fi
« Ответ #1 : 26 Июня 2015, 01:25:45 »
Пакет firmware-b43-installer стоит?
Бλог   @chuba_duba
 

Оффлайн mtc93rus

Re: Dell 610 wi fi
« Ответ #2 : 26 Июня 2015, 01:43:54 »
да ставил(ранее с убунтой помогало)

Cообщение объединено 26 Июня 2015, 01:44:42
ChubaDuba, да ставил(ранее с убунтой помогало)
 

Онлайн endru

Re: Dell 610 wi fi
« Ответ #3 : 26 Июня 2015, 06:32:18 »
команды под спойлер:
lspci -v
dpkg -l | grep b43

Оффлайн Александр Кряжев

Re: Dell 610 wi fi
« Ответ #4 : 26 Июня 2015, 09:39:02 »
Мне помогает такая последовательность:
Цитировать
1. Требуется узнать, название устройства.

lspci -kv

В моём случае, показало нечто такое:

    Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)

2. Открываем Synaptic и вставляем в поиск <BCM4313>. Увидим пакет, типа <firmware...>  и т.д. Его и устанавливаем.
3. Всё. После перезагрузки, есть wi-fi.
 

Оффлайн mtc93rus

Re: Dell 610 wi fi
« Ответ #5 : 26 Июня 2015, 13:37:55 »

Cообщение объединено 26 Июня 2015, 13:40:34
Мне помогает такая последовательность:
Цитировать
1. Требуется узнать, название устройства.

lspci -kv

В моём случае, показало нечто такое:

    Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)

2. Открываем Synaptic и вставляем в поиск <BCM4313>. Увидим пакет, типа <firmware...>  и т.д. Его и устанавливаем.
3. Всё. После перезагрузки, есть wi-fi.

выдал пакет firmware-b43-installer  , который уже установлен...

Cообщение объединено 26 Июня 2015, 13:41:28
03:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
   Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card
   Flags: bus master, fast devsel, latency 64, IRQ 17
   Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K]
   Kernel driver in use: b43-pci-bridge

dpkg -l | grep b43
ii  b43-fwcutter                          1:019-2                              i386         utility for extracting Broadcom 43xx firmware
ii  firmware-b43-installer                1:019-2                              all          firmware installer for the b43 driver

03:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
   Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card
   Flags: bus master, fast devsel, latency 64, IRQ 17
   Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K]
   Kernel driver in use: b43-pci-bridge

dpkg -l | grep b43
ii  b43-fwcutter                          1:019-2                              i386         utility for extracting Broadcom 43xx firmware
ii  firmware-b43-installer                1:019-2                              all          firmware installer for the b43 driver


Единственное чт, в убунте еще правил blacklist, но тут его не нашел
« Последнее редактирование: 26 Июня 2015, 13:49:03 от mtc93rus »
 

Оффлайн Александр Кряжев

Re: Dell 610 wi fi
« Ответ #6 : 26 Июня 2015, 13:54:59 »
выдал пакет firmware-b43-installer  , который уже установлен...
В моём случае, нашёлся пакет firmware-brcm80211, который и является драйвером. Странно.
 

Оффлайн mtc93rus

Re: Dell 610 wi fi
« Ответ #7 : 26 Июня 2015, 15:56:04 »
выдал пакет firmware-b43-installer  , который уже установлен...
В моём случае, нашёлся пакет firmware-brcm80211, который и является драйвером. Странно.
поставил этот пакет, но не помогло.
 

Оффлайн ChubaDuba

Re: Dell 610 wi fi
« Ответ #8 : 26 Июня 2015, 22:18:26 »
Показывайте вывод:
iwconfig
ifconfig
« Последнее редактирование: 26 Июня 2015, 22:21:34 от ChubaDuba »
Бλог   @chuba_duba
 

Оффлайн VKH

Re: Dell 610 wi fi
« Ответ #9 : 27 Июня 2015, 15:57:16 »
Привет. в первый раз когда ставил Debian, так же не смог настроить способ установить нормально wifi. Были проблемы с тем что пропадал сигнал... Потом нашел инструкции. Все делал по инструкции. Сейчас wifi работает как часы.
https://wiki.debian.org/wl
lspci -kv, выдает следующий модуль:
Spoiler: ShowHide
Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)
   Subsystem: Hewlett-Packard Company Device 1795
   Flags: bus master, fast devsel, latency 0, IRQ 16
   Memory at f0200000 (64-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: wl

Так что попробуй по данной инструкции!
 

Оффлайн mtc93rus

Re: Dell 610 wi fi
« Ответ #10 : 28 Июня 2015, 14:48:40 »
Показывайте вывод:
iwconfig
ifconfig


ifconfig

eth0      Link encap:Ethernet  HWaddr 00:12:3f:06:2b:76 
          inet addr:192.168.1.39  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fdad:b717:a321:0:212:3fff:fe06:2b76/64 Scope:Global
          inet6 addr: fe80::212:3fff:fe06:2b76/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2457 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2326 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2159460 (2.0 MiB)  TX bytes:338882 (330.9 KiB)
          Interrupt:16

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:34 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:3564 (3.4 KiB)  TX bytes:3564 (3.4 KiB)

iwconfig

wlan0     IEEE 802.11bg  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on
         
lo        no wireless extensions.

eth0      no wireless extensions.


Cообщение объединено 28 Июня 2015, 14:56:29
не помогло, к сожалению.
Привет. в первый раз когда ставил Debian, так же не смог настроить способ установить нормально wifi. Были проблемы с тем что пропадал сигнал... Потом нашел инструкции. Все делал по инструкции. Сейчас wifi работает как часы.
https://wiki.debian.org/wl
lspci -kv, выдает следующий модуль:
Spoiler: ShowHide
Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)
   Subsystem: Hewlett-Packard Company Device 1795
   Flags: bus master, fast devsel, latency 0, IRQ 16
   Memory at f0200000 (64-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: wl

Так что попробуй по данной инструкции!

« Последнее редактирование: 29 Июня 2015, 06:03:59 от endru »
 

Оффлайн VKH

Re: Dell 610 wi fi
« Ответ #11 : 28 Июня 2015, 19:12:51 »
через синаптик удали драйвера wifi и покажи вывод:
dmesg | grep -i error
dmesg —level=err
Я ставил сразу после установки. В общем, получив вывод, определил какой нужно ставить драйвер. В моем случае это wl.

Так же в ссылке https://wiki.debian.org/wl в пунтке "See Also" присутствуют другие инструкции по установке драйверов wifi для данного модуля. wireless-tools - должен установиться автоматом во время установки ОС.
 

Оффлайн mtc93rus

Re: Dell 610 wi fi
« Ответ #12 : 28 Июня 2015, 21:55:06 »
dmesg | grep -i error
в описании драйвера нет выбора моей карты или это неважно?
Вывод комманд
Spoiler: ShowHide
dmesg | grep -i error
[    7.850502] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   10.931902] radeon 0000:01:00.0: Direct firmware load failed with error -2
[   10.933966] [drm:r100_cp_init] *ERROR* Failed to load firmware!

dmesg —level=err
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt11-1 (2015-05-24)
[    0.000000] Disabled fast string operations
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000005ffd17ff] usable
[    0.000000] BIOS-e820: [mem 0x000000005ffd1800-0x000000005fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000f0006fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f0008000-0x00000000f000bfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec0ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fee0ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.3 present.
[    0.000000] DMI: Dell Inc. Latitude D610                   /      , BIOS A06 10/02/2005
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x5ffd1 max_arch_pfn = 0x1000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FC0000000 write-back
[    0.000000]   1 base 040000000 mask FE0000000 write-back
[    0.000000]   2 base 0FEDA0000 mask FFFFE0000 write-through
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] PAT not supported by CPU.
[    0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] init_memory_mapping: [mem 0x36200000-0x363fffff]
[    0.000000]  [mem 0x36200000-0x363fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x34000000-0x361fffff]
[    0.000000]  [mem 0x34000000-0x361fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x33ffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x33ffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x36400000-0x375fdfff]
[    0.000000]  [mem 0x36400000-0x373fffff] page 2M
[    0.000000]  [mem 0x37400000-0x375fdfff] page 4k
[    0.000000] BRK [0x01798000, 0x01798fff] PGTABLE
[    0.000000] BRK [0x01799000, 0x0179afff] PGTABLE
[    0.000000] BRK [0x0179b000, 0x0179bfff] PGTABLE
[    0.000000] BRK [0x0179c000, 0x0179cfff] PGTABLE
[    0.000000] RAMDISK: [mem 0x36416000-0x37202fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x000FC9B0 000014 (v00 DELL  )
[    0.000000] ACPI: RSDT 0x5FFD1F90 000040 (v01 DELL   CPi R    27D50A02 ASL  00000061)
[    0.000000] ACPI: FACP 0x5FFD2C00 000074 (v01 DELL   CPi R    27D50A02 ASL  00000061)
[    0.000000] ACPI: DSDT 0x5FFD3800 003C51 (v01 INT430 SYSFexxx 00001001 MSFT 0100000E)
[    0.000000] ACPI: FACS 0x5FFE2000 000040
[    0.000000] ACPI: APIC 0x5FFD3400 000068 (v01 DELL   CPi R    27D50A02 ASL  00000047)
[    0.000000] ACPI: ASF! 0x5FFD3000 00005B (v16 DELL   CPi R    27D50A02 ASL  00000061)
[    0.000000] ACPI: MCFG 0x5FFD33C0 00003E (v16 DELL   CPi R    27D50A02 ASL  00000061)
[    0.000000] ACPI: SSDT 0x5FFD23E6 00023E (v01 PmRef  Cpu0Ist  00003000 INTL 20030522)
[    0.000000] ACPI: SSDT 0x5FFD220E 0001D8 (v01 PmRef  Cpu0Cst  00003001 INTL 20030522)
[    0.000000] ACPI: SSDT 0x5FFD2013 0001FB (v01 PmRef  CpuPm    00003000 INTL 20030522)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 649MB HIGHMEM available.
[    0.000000] 885MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 375fe000
[    0.000000]   low ram: 0 - 375fe000
[    0.000000] BRK [0x0179d000, 0x0179dfff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x375fdfff]
[    0.000000]   HighMem  [mem 0x375fe000-0x5ffd0fff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0x5ffd0fff]
[    0.000000] On node 0 totalpages: 393071
[    0.000000] free_area_init_node: node 0, pgdat c1658ec0, node_mem_map f5816020
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   Normal zone: 1740 pages used for memmap
[    0.000000]   Normal zone: 222718 pages, LIFO batch:31
[    0.000000]   HighMem zone: 1300 pages used for memmap
[    0.000000]   HighMem zone: 166355 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] smpboot: Allowing 2 CPUs, 1 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.000000] e820: [mem 0x60000000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @f75d9000 s34752 r0 d22592 u57344
[    0.000000] pcpu-alloc: s34752 r0 d22592 u57344 alloc=14*4096
[    0.000000] pcpu-alloc:
  • 0
  • 1

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 391299
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-686-pae root=UUID=6da861f7-42fb-450b-8753-d9f2ca7d1d1e ro quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000375fe:0005ffd1)
[    0.000000] Initializing Movable for node 0 (00000000:00000000)
[    0.000000] Memory: 1536932K/1572284K available (4599K kernel code, 518K rwdata, 1448K rodata, 656K init, 460K bss, 35352K reserved, 665420K highmem)
[    0.000000] virtual kernel memory layout:
    fixmap  : 0xffd36000 - 0xfffff000   (2852 kB)
    pkmap   : 0xff600000 - 0xff800000   (2048 kB)
    vmalloc : 0xf7dfe000 - 0xff5fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf75fe000   ( 885 MB)
      .init : 0xc166d000 - 0xc1711000   ( 656 kB)
      .data : 0xc147e240 - 0xc166b880   (1973 kB)
      .text : 0xc1000000 - 0xc147e240   (4600 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] Hierarchical RCU implementation.
[    0.000000]    RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]    RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:2304 nr_irqs:512 16
[    0.000000] CPU 0 irqstacks, hard=f5406000 soft=f5408000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1595.986 MHz processor
[    0.008015] Calibrating delay loop (skipped), value calculated using timer frequency.. 3191.97 BogoMIPS (lpj=6383944)
[    0.008021] pid_max: default: 32768 minimum: 301
[    0.008041] ACPI: Core revision 20140424
[    0.018696] ACPI: All ACPI Tables successfully acquired
[    0.020048] Security Framework initialized
[    0.020067] AppArmor: AppArmor disabled by boot time parameter
[    0.020070] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.020101] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.020105] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.020547] Initializing cgroup subsys memory
[    0.020558] Initializing cgroup subsys devices
[    0.020573] Initializing cgroup subsys freezer
[    0.020580] Initializing cgroup subsys net_cls
[    0.020590] Initializing cgroup subsys blkio
[    0.020600] Initializing cgroup subsys perf_event
[    0.020605] Initializing cgroup subsys net_prio
[    0.020643] Disabled fast string operations
[    0.020654] mce: CPU supports 5 MCE banks
[    0.020666] CPU0: Thermal monitoring enabled (TM1)
[    0.020679] Last level iTLB entries: 4KB 128, 2MB 0, 4MB 2
Last level dTLB entries: 4KB 128, 2MB 0, 4MB 8, 1GB 0
tlb_flushall_shift: 6
[    0.032805] ftrace: allocating 20754 entries in 41 pages
[    0.040115] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.040570] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.081595] smpboot: CPU0: Intel(R) Pentium(R) M processor 1.60GHz (fam: 06, model: 0d, stepping: 08)
[    0.084000] Performance Events: p6 PMU driver.
[    0.084000] ... version:                0
[    0.084000] ... bit width:              32
[    0.084000] ... generic registers:      2
[    0.084000] ... value mask:             00000000ffffffff
[    0.084000] ... max period:             000000007fffffff
[    0.084000] ... fixed-purpose events:   0
[    0.084000] ... event mask:             0000000000000003
[    0.084000] x86: Booted up 1 node, 1 CPUs
[    0.084000] smpboot: Total of 1 processors activated (3191.97 BogoMIPS)
[    0.084000] devtmpfs: initialized
[    0.084238] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.086296] pinctrl core: initialized pinctrl subsystem
[    0.086412] NET: Registered protocol family 16
[    0.086606] cpuidle: using governor ladder
[    0.086610] cpuidle: using governor menu
[    0.086697] ACPI: bus type PCI registered
[    0.086701] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.086834] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.086839] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.086841] PCI: Using MMCONFIG for extended config space
[    0.086843] PCI: Using configuration type 1 for base access
[    0.086859] dmi type 0xB1 record - unknown flag
[    0.088587] ACPI: Added _OSI(Module Device)
[    0.088591] ACPI: Added _OSI(Processor Device)
[    0.088594] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.088597] ACPI: Added _OSI(Processor Aggregator Device)
[    0.099117] ACPI: Dynamic OEM Table Load:
[    0.099125] ACPI: SSDT 0xF553E540 000043 (v01 LMPWR  DELLLOM  00001001 INTL 20030522)
[    0.099813] ACPI: Interpreter enabled
[    0.099829] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
[    0.099836] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.099857] ACPI: (supports S0 S3 S4 S5)
[    0.099860] ACPI: Using IOAPIC for interrupt routing
[    0.099902] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.128715] acpi LNXIOBAY:00: ACPI dock station (docks/bays count: 1)
[    0.133736] acpi PNP0C15:00: ACPI dock station (docks/bays count: 2)
[    0.143718] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.143726] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.143735] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.161329] acpi PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.161334] acpi PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.161338] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.161341] acpi PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[    0.161345] acpi PNP0A03:00: host bridge window [mem 0x60000000-0xdfffffff] (ignored)
[    0.161349] acpi PNP0A03:00: host bridge window [mem 0xf0007000-0xf0007fff] (ignored)
[    0.161353] acpi PNP0A03:00: host bridge window [mem 0xf000c000-0xfebfffff] (ignored)
[    0.161356] acpi PNP0A03:00: host bridge window [mem 0xfec10000-0xfed1ffff] (ignored)
[    0.161360] acpi PNP0A03:00: host bridge window [mem 0xfee10000-0xffafffff] (ignored)
[    0.161363] PCI: root bus 00: using default resources
[    0.161655] PCI host bridge to bus 0000:00
[    0.161660] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.161664] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.161668] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[    0.161681] pci 0000:00:00.0: [8086:2590] type 00 class 0x060000
[    0.161838] pci 0000:00:01.0: [8086:2591] type 01 class 0x060400
[    0.161889] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.162072] pci 0000:00:1c.0: [8086:2660] type 01 class 0x060400
[    0.162187] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.162347] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300
[    0.162402] pci 0000:00:1d.0: reg 0x20: [io  0xbf80-0xbf9f]
[    0.162513] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.162597] pci 0000:00:1d.1: [8086:2659] type 00 class 0x0c0300
[    0.162652] pci 0000:00:1d.1: reg 0x20: [io  0xbf60-0xbf7f]
[    0.162760] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.162843] pci 0000:00:1d.2: [8086:265a] type 00 class 0x0c0300
[    0.162898] pci 0000:00:1d.2: reg 0x20: [io  0xbf40-0xbf5f]
[    0.163007] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.163088] pci 0000:00:1d.3: [8086:265b] type 00 class 0x0c0300
[    0.163143] pci 0000:00:1d.3: reg 0x20: [io  0xbf20-0xbf3f]
[    0.163252] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.163347] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320
[    0.163373] pci 0000:00:1d.7: reg 0x10: [mem 0xffa80800-0xffa80bff]
[    0.163475] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.163563] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.163651] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.163786] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.163875] pci 0000:00:1e.2: [8086:266e] type 00 class 0x040100
[    0.163896] pci 0000:00:1e.2: reg 0x10: [io  0xed00-0xedff]
[    0.163909] pci 0000:00:1e.2: reg 0x14: [io  0xec40-0xec7f]
[    0.163923] pci 0000:00:1e.2: reg 0x18: [mem 0xdffffe00-0xdfffffff]
[    0.163936] pci 0000:00:1e.2: reg 0x1c: [mem 0xdffffd00-0xdffffdff]
[    0.163998] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[    0.164143] pci 0000:00:1e.3: [8086:266d] type 00 class 0x070300
[    0.164165] pci 0000:00:1e.3: reg 0x10: [io  0xee00-0xeeff]
[    0.164178] pci 0000:00:1e.3: reg 0x14: [io  0xec80-0xecff]
[    0.164258] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold
[    0.164325] pci 0000:00:1e.3: System wakeup disabled by ACPI
[    0.164416] pci 0000:00:1f.0: [8086:2641] type 00 class 0x060100
[    0.164523] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.164533] pci 0000:00:1f.0: quirk: [io  0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
[    0.164540] pci 0000:00:1f.0: quirk: [io  0x1080-0x10bf] claimed by ICH6 GPIO
[    0.164546] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0900-097f
[    0.164690] pci 0000:00:1f.2: [8086:2653] type 00 class 0x010180
[    0.164712] pci 0000:00:1f.2: reg 0x10: [io  0x01f0-0x01f7]
[    0.164725] pci 0000:00:1f.2: reg 0x14: [io  0x03f4-0x03f7]
[    0.164737] pci 0000:00:1f.2: reg 0x18: [io  0x0170-0x0177]
[    0.164750] pci 0000:00:1f.2: reg 0x1c: [io  0x0374-0x0377]
[    0.164763] pci 0000:00:1f.2: reg 0x20: [io  0xbfa0-0xbfaf]
[    0.164789] pci 0000:00:1f.2: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.164792] pci 0000:00:1f.2: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.164796] pci 0000:00:1f.2: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.164799] pci 0000:00:1f.2: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.164831] pci 0000:00:1f.2: PME# supported from D3hot
[    0.165062] pci 0000:01:00.0: [1002:5460] type 00 class 0x030000
[    0.165077] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xd7ffffff pref]
[    0.165086] pci 0000:01:00.0: reg 0x14: [io  0xde00-0xdeff]
[    0.165096] pci 0000:01:00.0: reg 0x18: [mem 0xdfdf0000-0xdfdfffff]
[    0.165122] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.165158] pci 0000:01:00.0: supports D1 D2
[    0.165243] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.165253] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.165257] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.165262] pci 0000:00:01.0:   bridge window [mem 0xdfd00000-0xdfefffff]
[    0.165267] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd7ffffff pref]
[    0.165416] pci 0000:02:00.0: [14e4:1677] type 00 class 0x020000
[    0.165454] pci 0000:02:00.0: reg 0x10: [mem 0xdfcf0000-0xdfcfffff 64bit]
[    0.165634] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.165672] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.165750] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.165764] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.165773] pci 0000:00:1c.0:   bridge window [mem 0xdfc00000-0xdfcfffff]
[    0.165908] pci 0000:03:01.0: [104c:8036] type 02 class 0x060700
[    0.165931] pci 0000:03:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
[    0.165974] pci 0000:03:01.0: supports D1 D2
[    0.165978] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.166100] pci 0000:03:01.5: [104c:8038] type 00 class 0x078000
[    0.166127] pci 0000:03:01.5: reg 0x10: [mem 0xdfbfc000-0xdfbfcfff]
[    0.166143] pci 0000:03:01.5: reg 0x14: [mem 0xdfbfd000-0xdfbfdfff]
[    0.166245] pci 0000:03:01.5: supports D1 D2
[    0.166248] pci 0000:03:01.5: PME# supported from D0 D1 D2 D3hot
[    0.166362] pci 0000:03:03.0: [14e4:4318] type 00 class 0x028000
[    0.166380] pci 0000:03:03.0: reg 0x10: [mem 0xdfbfe000-0xdfbfffff]
[    0.166570] pci 0000:00:1e.0: PCI bridge to [bus 03-04] (subtractive decode)
[    0.166579] pci 0000:00:1e.0:   bridge window [mem 0xdfb00000-0xdfbfffff]
[    0.166588] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.166592] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[    0.166675] pci_bus 0000:04: busn_res: can not insert [bus 04-ff] under [bus 03-04] (conflicts with (null) [bus 03-04])
[    0.166683] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 07
[    0.166687] pci_bus 0000:04: busn_res: can not insert [bus 04-07] under [bus 03-04] (conflicts with (null) [bus 03-04])
[    0.166694] pci_bus 0000:04: [bus 04-07] partially hidden behind transparent bridge 0000:03 [bus 03-04]
[    0.166700] pci 0000:00:1e.0: bridge has subordinate 04 but max busn 07
[    0.166723] pci_bus 0000:00: on NUMA node 0
[    0.176442] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[    0.176584] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[    0.176722] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[    0.176861] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[    0.176982] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.177107] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.177231] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.178685] ACPI: Enabled 2 GPEs in block 00 to 1F
[    0.178905] vgaarb: setting as boot device: PCI:0000:01:00.0
[    0.178909] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.178912] vgaarb: loaded
[    0.178915] vgaarb: bridge control possible 0000:01:00.0
[    0.179009] PCI: Using ACPI for IRQ routing
[    0.189563] PCI: pci_cache_line_size set to 64 bytes
[    0.189628] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[    0.189632] e820: reserve RAM buffer [mem 0x5ffd1800-0x5fffffff]
[    0.190041] hpet clockevent registered
[    0.190046] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.190053] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.190059] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.192029] Switched to clocksource hpet
[    0.202763] pnp: PnP ACPI init
[    0.202790] ACPI: bus type PNP registered
[    0.214249] system 00:00: [mem 0x00000000-0x0009fbff] could not be reserved
[    0.214255] system 00:00: [mem 0x0009fc00-0x0009ffff] could not be reserved
[    0.214260] system 00:00: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.214264] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.214269] system 00:00: [mem 0x00100000-0x5ffd17ff] could not be reserved
[    0.214273] system 00:00: [mem 0x5ffd1800-0x5fffffff] has been reserved
[    0.214277] system 00:00: [mem 0xfeda0000-0xfedfffff] has been reserved
[    0.214282] system 00:00: [mem 0xffb00000-0xffffffff] has been reserved
[    0.214286] system 00:00: [mem 0xfec00000-0xfec0ffff] could not be reserved
[    0.214291] system 00:00: [mem 0xfee00000-0xfee0ffff] has been reserved
[    0.214295] system 00:00: [mem 0xfed20000-0xfed9ffff] has been reserved
[    0.214299] system 00:00: [mem 0xf0000000-0xf0003fff] has been reserved
[    0.214304] system 00:00: [mem 0xf0004000-0xf0004fff] has been reserved
[    0.214308] system 00:00: [mem 0xf0005000-0xf0005fff] has been reserved
[    0.214312] system 00:00: [mem 0xf0006000-0xf0006fff] has been reserved
[    0.214317] system 00:00: [mem 0xf0008000-0xf000bfff] has been reserved
[    0.214321] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[    0.214328] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.214380] pnp 00:01: disabling [io  0x1000-0x1005] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.214385] pnp 00:01: disabling [io  0x1008-0x100f] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.214442] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.214447] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.214489] pnp 00:02: disabling [io  0x1006-0x1007] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.214493] pnp 00:02: disabling [io  0x100a-0x1059] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.214498] pnp 00:02: disabling [io  0x1060-0x107f] because it overlaps 0000:00:1f.0 BAR 13 [io  0x1000-0x107f]
[    0.214552] system 00:02: [io  0xf400-0xf4fe] has been reserved
[    0.214557] system 00:02: [io  0x1080-0x10bf] has been reserved
[    0.214561] system 00:02: [io  0x10c0-0x10df] has been reserved
[    0.214565] system 00:02: [io  0x10e0-0x10ff] could not be reserved
[    0.214570] system 00:02: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.214654] pnp 00:03: Plug and Play ACPI device, IDs PNP0f13 (active)
[    0.214726] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.214797] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.214891] system 00:06: [io  0x0900-0x090f] has been reserved
[    0.214896] system 00:06: [io  0x0910-0x091f] has been reserved
[    0.214900] system 00:06: [io  0x0920-0x092f] has been reserved
[    0.214904] system 00:06: [io  0x093c-0x093f] has been reserved
[    0.214909] system 00:06: [io  0x0940-0x097f] has been reserved
[    0.214913] system 00:06: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.220451] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.229391] pnp 00:08: [dma 1]
[    0.229537] pnp 00:08: Plug and Play ACPI device, IDs PNP0401 (active)
[    0.235515] system 00:09: [io  0x0930-0x093b] has been reserved
[    0.235521] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.237299] pnp: PnP ACPI: found 10 devices
[    0.237302] ACPI: bus type PNP unregistered
[    0.237313] PnPBIOS: Disabled by ACPI PNP
[    0.275136] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 02] add_size 1000
[    0.275144] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    0.275166] pci 0000:03:01.0: res[13]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.275170] pci 0000:03:01.0: res[14]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.275176] pci 0000:00:1e.0: bridge window [io  0x1000-0x0fff] to [bus 03-04] add_size 1000
[    0.275188] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.275192] pci 0000:00:1c.0: res[13]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.275196] pci 0000:00:1e.0: res[13]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.275207] pci 0000:00:1c.0: BAR 15: assigned [mem 0x60000000-0x601fffff 64bit pref]
[    0.275214] pci 0000:00:1c.0: BAR 13: assigned [io  0x2000-0x2fff]
[    0.275219] pci 0000:00:1e.0: BAR 13: assigned [io  0x3000-0x3fff]
[    0.275226] pci 0000:01:00.0: BAR 6: assigned [mem 0xdfd00000-0xdfd1ffff pref]
[    0.275231] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.275235] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.275240] pci 0000:00:01.0:   bridge window [mem 0xdfd00000-0xdfefffff]
[    0.275245] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd7ffffff pref]
[    0.275251] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.275255] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    0.275263] pci 0000:00:1c.0:   bridge window [mem 0xdfc00000-0xdfcfffff]
[    0.275269] pci 0000:00:1c.0:   bridge window [mem 0x60000000-0x601fffff 64bit pref]
[    0.275282] pci 0000:03:01.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000
[    0.275286] pci 0000:03:01.0: res[16]=[mem 0x04000000-0x03ffffff] get_res_add_size add_size 4000000
[    0.275290] pci 0000:03:01.0: res[13]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.275294] pci 0000:03:01.0: res[14]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.275300] pci 0000:03:01.0: BAR 0: assigned [mem 0xf4000000-0xf4000fff]
[    0.275310] pci 0000:03:01.0: BAR 15: assigned [mem 0xf8000000-0xfbffffff pref]
[    0.275318] pci 0000:03:01.0: BAR 16: assigned [mem 0x64000000-0x67ffffff]
[    0.275322] pci 0000:03:01.0: BAR 13: assigned [io  0x3000-0x30ff]
[    0.275326] pci 0000:03:01.0: BAR 14: assigned [io  0x3400-0x34ff]
[    0.275330] pci 0000:03:01.0: CardBus bridge to [bus 04-07]
[    0.275334] pci 0000:03:01.0:   bridge window [io  0x3000-0x30ff]
[    0.275341] pci 0000:03:01.0:   bridge window [io  0x3400-0x34ff]
[    0.275348] pci 0000:03:01.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    0.275355] pci 0000:03:01.0:   bridge window [mem 0x64000000-0x67ffffff]
[    0.275361] pci 0000:00:1e.0: PCI bridge to [bus 03-04]
[    0.275366] pci 0000:00:1e.0:   bridge window [io  0x3000-0x3fff]
[    0.275373] pci 0000:00:1e.0:   bridge window [mem 0xdfb00000-0xdfbfffff]
[    0.275386] pci_bus 0000:00: resource 4 [io  0x0000-0xffff]
[    0.275390] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[    0.275394] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.275397] pci_bus 0000:01: resource 1 [mem 0xdfd00000-0xdfefffff]
[    0.275401] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xd7ffffff pref]
[    0.275405] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.275409] pci_bus 0000:02: resource 1 [mem 0xdfc00000-0xdfcfffff]
[    0.275412] pci_bus 0000:02: resource 2 [mem 0x60000000-0x601fffff 64bit pref]
[    0.275416] pci_bus 0000:03: resource 0 [io  0x3000-0x3fff]
[    0.275420] pci_bus 0000:03: resource 1 [mem 0xdfb00000-0xdfbfffff]
[    0.275423] pci_bus 0000:03: resource 4 [io  0x0000-0xffff]
[    0.275427] pci_bus 0000:03: resource 5 [mem 0x00000000-0xffffffff]
[    0.275431] pci_bus 0000:04: resource 0 [io  0x3000-0x30ff]
[    0.275434] pci_bus 0000:04: resource 1 [io  0x3400-0x34ff]
[    0.275438] pci_bus 0000:04: resource 2 [mem 0xf8000000-0xfbffffff pref]
[    0.275442] pci_bus 0000:04: resource 3 [mem 0x64000000-0x67ffffff]
[    0.275488] NET: Registered protocol family 2
[    0.275887] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.275920] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.275979] TCP: Hash tables configured (established 8192 bind 8192)
[    0.276032] TCP: reno registered
[    0.276036] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.276052] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.276137] NET: Registered protocol family 1
[    0.278182] pci 0000:01:00.0: Video device with shadowed ROM
[    0.278201] PCI: CLS 64 bytes, default 64
[    0.278278] Unpacking initramfs...
[    0.795421] Freeing initrd memory: 14260K (f6416000 - f7203000)
[    0.795702] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
[    0.795813] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.796359] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.796428] audit: initializing netlink subsys (disabled)
[    0.796466] audit: type=2000 audit(1435517319.796:1): initialized
[    0.796964] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.796990] zbud: loaded
[    0.797091] VFS: Disk quotas dquot_6.5.2
[    0.797114] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.797207] msgmni has been set to 1730
[    0.797689] alg: No test for stdrng (krng)
[    0.797723] bounce: pool size: 64 pages
[    0.797742] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.797803] io scheduler noop registered
[    0.797807] io scheduler deadline registered
[    0.797860] io scheduler cfq registered (default)
[    0.797982] pcieport 0000:00:01.0: device [8086:2591] has invalid IRQ; check vendor BIOS
[    0.798265] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.798344] pcieport 0000:00:1c.0: device [8086:2660] has invalid IRQ; check vendor BIOS
[    0.798562] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.798727] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.798762] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.798802] intel_idle: does not run on family 6 model 13
[    0.798875] GHES: HEST is not enabled!
[    0.798910] isapnp: Scanning for PnP cards...
[    1.152714] isapnp: No Plug & Play device found
[    1.152840] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.173440] 00:07: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.174440] Linux agpgart interface v0.103
[    1.174826] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.180125] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.180134] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.180352] mousedev: PS/2 mouse device common for all mice
[    1.180600] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    1.180636] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.180658] ledtrig-cpu: registered to indicate activity on CPUs
[    1.181559] TCP: cubic registered
[    1.181582] NET: Registered protocol family 10
[    1.181929] mip6: Mobile IPv6
[    1.181934] NET: Registered protocol family 17
[    1.181943] mpls_gso: MPLS GSO support
[    1.182158] Using IPI No-Shortcut mode
[    1.182330] registered taskstats version 1
[    1.182840] rtc_cmos 00:05: setting system clock to 2015-06-28 18:48:40 UTC (1435517320)
[    1.182933] PM: Hibernation image not present or could not be loaded.
[    1.183352] Freeing unused kernel memory: 656K (c166d000 - c1711000)
[    1.183406] Write protecting the kernel text: 4604k
[    1.183459] Write protecting the kernel read-only data: 1452k
[    1.183461] NX-protecting the kernel data: 3588k
[    1.186201] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.200195] systemd-udevd[54]: starting version 215
[    1.200710] random: systemd-udevd urandom read with 0 bits of entropy available
[    1.222615] ACPI: bus type USB registered
[    1.222667] usbcore: registered new interface driver usbfs
[    1.222694] usbcore: registered new interface driver hub
[    1.235904] usbcore: registered new device driver usb
[    1.236826] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.237300] uhci_hcd: USB Universal Host Controller Interface driver
[    1.237592] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.237604] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.237616] uhci_hcd 0000:00:1d.0: detected 2 ports
[    1.237664] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[    1.238058] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.238062] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.238066] usb usb1: Product: UHCI Host Controller
[    1.238069] usb usb1: Manufacturer: Linux 3.16.0-4-686-pae uhci_hcd
[    1.238072] usb usb1: SerialNumber: 0000:00:1d.0
[    1.238457] hub 1-0:1.0: USB hub found
[    1.238469] hub 1-0:1.0: 2 ports detected
[    1.239601] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.239612] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    1.239621] uhci_hcd 0000:00:1d.1: detected 2 ports
[    1.239663] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[    1.241134] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.241139] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.241142] usb usb2: Product: UHCI Host Controller
[    1.241146] usb usb2: Manufacturer: Linux 3.16.0-4-686-pae uhci_hcd
[    1.241149] usb usb2: SerialNumber: 0000:00:1d.1
[    1.241357] hub 2-0:1.0: USB hub found
[    1.241367] hub 2-0:1.0: 2 ports detected
[    1.241763] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.241773] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    1.241781] uhci_hcd 0000:00:1d.2: detected 2 ports
[    1.241819] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[    1.242281] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.242285] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.242289] usb usb3: Product: UHCI Host Controller
[    1.242292] usb usb3: Manufacturer: Linux 3.16.0-4-686-pae uhci_hcd
[    1.242295] usb usb3: SerialNumber: 0000:00:1d.2
[    1.243457] hub 3-0:1.0: USB hub found
[    1.243471] hub 3-0:1.0: 2 ports detected
[    1.243862] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.243871] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    1.243879] uhci_hcd 0000:00:1d.3: detected 2 ports
[    1.243917] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[    1.244850] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.244855] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.244859] usb usb4: Product: UHCI Host Controller
[    1.244862] usb usb4: Manufacturer: Linux 3.16.0-4-686-pae uhci_hcd
[    1.244865] usb usb4: SerialNumber: 0000:00:1d.3
[    1.245620] hub 4-0:1.0: USB hub found
[    1.245630] hub 4-0:1.0: 2 ports detected
[    1.258456] pps_core: LinuxPPS API ver. 1 registered
[    1.258461] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.258739] PTP clock support registered
[    1.260314] tg3.c:v3.137 (May 11, 2014)
[    1.261583] ehci-pci: EHCI PCI platform driver
[    1.262271] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.262281] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    1.262299] ehci-pci 0000:00:1d.7: debug port 1
[    1.266214] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    1.266230] ehci-pci 0000:00:1d.7: irq 16, io mem 0xffa80800
[    1.270041] SCSI subsystem initialized
[    1.276049] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.276161] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    1.276166] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.276169] usb usb5: Product: EHCI Host Controller
[    1.276172] usb usb5: Manufacturer: Linux 3.16.0-4-686-pae ehci_hcd
[    1.276176] usb usb5: SerialNumber: 0000:00:1d.7
[    1.276425] hub 5-0:1.0: USB hub found
[    1.276436] hub 5-0:1.0: 8 ports detected
[    1.282394] thermal LNXTHERM:00: registered as thermal_zone0
[    1.282399] ACPI: Thermal Zone [THM] (43 C)
[    1.288934] libata version 3.00 loaded.
[    1.293303] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM95751) rev 4001] (PCI Express) MAC address 00:12:3f:06:2b:76
[    1.293309] tg3 0000:02:00.0 eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    1.293313] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    1.293317] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    1.300140] hub 1-0:1.0: USB hub found
[    1.300153] hub 1-0:1.0: 2 ports detected
[    1.324115] hub 2-0:1.0: USB hub found
[    1.324128] hub 2-0:1.0: 2 ports detected
[    1.348094] hub 3-0:1.0: USB hub found
[    1.348105] hub 3-0:1.0: 2 ports detected
[    1.372091] hub 4-0:1.0: USB hub found
[    1.372102] hub 4-0:1.0: 2 ports detected
[    1.372643] ahci 0000:00:1f.2: version 3.0
[    1.372868] ahci 0000:00:1f.2: controller is in combined mode, can't enable AHCI mode
[    1.373636] ata_piix 0000:00:1f.2: version 2.13
[    1.373829] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    1.529431] scsi0 : ata_piix
[    1.529634] scsi1 : ata_piix
[    1.529724] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[    1.529727] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[    1.692585] ata2.00: ATAPI: HL-DT-STCD-RW/DVD-ROM GCC-4243N, A102, max UDMA/33
[    1.708240] ata2.00: configured for UDMA/33
[    1.742475] ata1.00: ATA-7: WDC WD1600BEVE-00UYT0, 01.04A01, max UDMA/100
[    1.742479] ata1.00: 312581808 sectors, multi 8: LBA48
[    1.742484] ata1.00: applying bridge limits
[    1.756586] ata1.00: configured for UDMA/100
[    1.756724] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1600BEVE-0 4A01 PQ: 0 ANSI: 5
[    1.761501] scsi 1:0:0:0: CD-ROM            HL-DT-ST RW/DVD GCC-4243N A102 PQ: 0 ANSI: 5
[    1.776344] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.776420] sd 0:0:0:0: [sda] Write Protect is off
[    1.776424] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.776456] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.783937] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.783941] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.784175] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.785713] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.785815] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.792022] tsc: Refined TSC clocksource calibration: 1595.999 MHz
[    1.809518]  sda: sda1 sda2 < sda5 >
[    1.810169] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.900036] usb 4-1: new low-speed USB device number 2 using uhci_hcd
[    2.073051] usb 4-1: New USB device found, idVendor=09da, idProduct=000a
[    2.073057] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.073060] usb 4-1: Product: PS/2+USB Mouse
[    2.073063] usb 4-1: Manufacturer: A4Tech
[    2.088279] hidraw: raw HID events driver (C) Jiri Kosina
[    2.101326] usbcore: registered new interface driver usbhid
[    2.101329] usbhid: USB HID core driver
[    2.209830] PM: Starting manual resume from disk
[    2.209838] PM: Hibernation image partition 8:5 present
[    2.209840] PM: Looking for hibernation image.
[    2.210152] PM: Image not found (code -22)
[    2.210155] PM: Hibernation image not present or could not be loaded.
[    2.377259] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    2.792062] Switched to clocksource tsc
[    3.854241] random: nonblocking pool is initialized
[    5.745724] lp: driver loaded but no devices found
[    5.801908] ppdev: user-space parallel port driver
[    5.842839] parport_pc 00:08: reported by Plug and Play ACPI
[    5.842908] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[    5.936155] lp0: using parport0 (interrupt-driven).
[    6.027472] fuse init (API version 7.23)
[    6.194854] systemd-udevd[151]: starting version 215
[    7.850502] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    8.001428] systemd-journald[141]: Received request to flush runtime journal from PID 1
[    8.165221] tsc: Marking TSC unstable due to TSC halts in idle
[    8.165243] ACPI: acpi_idle registered with cpuidle
[    8.171594] Switched to clocksource hpet
[    8.517480] ACPI: AC Adapter [AC] (on-line)
[    8.639825] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.666808] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[    8.667138] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:20/LNXVIDEO:00/input/input2
[    8.667282] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
[    8.764071] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[    8.764664] ACPI: Lid Switch [LID]
[    9.007606] NET: Registered protocol family 23
[    9.047526] ACPI: Battery Slot [BAT0] (battery present)
[    9.047665] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[    9.047672] ACPI: Power Button [PBTN]
[    9.047760] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
[    9.047765] ACPI: Sleep Button [SBTN]
[    9.051961] ACPI: Battery Slot [BAT1] (battery absent)
[    9.233463] [drm] Initialized drm 1.1.0 20060810
[    9.345593] yenta_cardbus 0000:03:01.0: enabling device (0000 -> 0003)
[    9.345845] yenta_cardbus 0000:03:01.0: CardBus bridge found [1028:0182]
[    9.345875] yenta_cardbus 0000:03:01.0: Using CSCINT to route CSC interrupts to PCI
[    9.345882] yenta_cardbus 0000:03:01.0: Routing CardBus interrupts to PCI
[    9.345893] yenta_cardbus 0000:03:01.0: TI: mfunc 0x01111122, devctl 0x64
[    9.470192] intel_rng: FWH not detected
[    9.576761] yenta_cardbus 0000:03:01.0: ISA IRQ mask 0x0c78, PCI irq 19
[    9.576774] yenta_cardbus 0000:03:01.0: Socket status: 30000006
[    9.576783] pci_bus 0000:03: Raising subordinate bus# of parent bus (#03) from #04 to #07
[    9.576801] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge window: [io  0x3000-0x3fff]
[    9.576810] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x3fff:
[    9.578157]  excluding 0x3000-0x30ff 0x3400-0x34ff
[    9.586660] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge window: [mem 0xdfb00000-0xdfbfffff]
[    9.586667] pcmcia_socket pcmcia_socket0: cs: memory probe 0xdfb00000-0xdfbfffff:
[    9.586681]  excluding 0xdfbf0000-0xdfbfffff
[    9.843118] [drm] radeon kernel modesetting enabled.
[    9.845595] [drm] initializing kernel modesetting (RV380 0x1002:0x5460 0x1028:0x2006).
[    9.845616] [drm] register mmio base: 0xDFDF0000
[    9.845620] [drm] register mmio size: 65536
[    9.845800] [drm] Generation 2 PCI interface, using max accessible memory
[    9.845811] radeon 0000:01:00.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (64M used)
[    9.845817] radeon 0000:01:00.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
[    9.849193] [drm] Detected VRAM RAM=128M, BAR=128M
[    9.849197] [drm] RAM width 64bits DDR
[    9.849661] [TTM] Zone  kernel: Available graphics memory: 443214 kiB
[    9.849664] [TTM] Zone highmem: Available graphics memory: 775924 kiB
[    9.849666] [TTM] Initializing pool allocator
[    9.849675] [TTM] Initializing DMA pool allocator
[    9.849708] [drm] radeon: 64M of VRAM memory ready
[    9.849711] [drm] radeon: 512M of GTT memory ready.
[    9.849732] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    9.850837] [drm] radeon: power management initialized
[    9.850862] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[    9.852401] [drm] PCIE GART of 512M enabled (table at 0x00000000D0040000).
[    9.856074] radeon 0000:01:00.0: WB enabled
[    9.856083] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xf4c5f000
[    9.856088] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    9.856090] [drm] Driver supports precise vblank timestamp query.
[    9.856093] radeon 0000:01:00.0: radeon: MSI limited to 32-bit
[    9.856120] radeon 0000:01:00.0: irq 42 for MSI/MSI-X
[    9.856136] radeon 0000:01:00.0: radeon: using MSI.
[    9.856168] [drm] radeon: irq initialized.
[    9.856187] [drm] Loading R300 Microcode
[   10.128086] snd_intel8x0m 0000:00:1e.3: MC'97 1 converters and GPIO not ready (0xff00)
[   10.129572] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   10.132516] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
[   10.132529] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
[   10.132538] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
[   10.132547] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[   10.132556] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[   10.172529] ssb: Sonics Silicon Backplane found on PCI device 0000:03:03.0
[   10.264538] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   10.686435] input: A4Tech PS/2+USB Mouse as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.0/0003:09DA:000A.0001/input/input8
[   10.687910] a4tech 0003:09DA:000A.0001: input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:1d.3-1/input0
[   10.711157] cfg80211: Calling CRDA to update world regulatory domain
[   10.825250] iTCO_vendor_support: vendor-support=0
[   10.841346] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   10.841625] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[   10.841982] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   10.931845] radeon 0000:01:00.0: firmware: failed to load radeon/R300_cp.bin (-2)
[   10.931902] radeon 0000:01:00.0: Direct firmware load failed with error -2
[   10.931907] radeon 0000:01:00.0: Falling back to user helper
[   10.933966] [drm:r100_cp_init] *ERROR* Failed to load firmware!
[   10.934017] radeon 0000:01:00.0: failed initializing CP (-12).
[   10.934063] radeon 0000:01:00.0: Disabling GPU acceleration
[   10.934113] [drm] radeon: cp finalized
[   10.935848] [drm] Panel ID String: H4400141XB
           
[   10.935855] [drm] Panel Size 1024x768
[   10.957614] [drm] radeon legacy LVDS backlight initialized
[   10.957620] [drm] Radeon Display Connectors
[   10.957624] [drm] Connector 0:
[   10.957626] [drm]   VGA-1
[   10.957631] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[   10.957634] [drm]   Encoders:
[   10.957637] [drm]     CRT1: INTERNAL_DAC1
[   10.957640] [drm] Connector 1:
[   10.957643] [drm]   DVI-D-1
[   10.957645] [drm]   HPD1
[   10.957650] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[   10.957652] [drm]   Encoders:
[   10.957655] [drm]     DFP1: INTERNAL_TMDS1
[   10.957658] [drm] Connector 2:
[   10.957661] [drm]   LVDS-1
[   10.957663] [drm]   Encoders:
[   10.957666] [drm]     LCD1: INTERNAL_LVDS
[   10.957669] [drm] Connector 3:
[   10.957671] [drm]   SVIDEO-1
[   10.957674] [drm]   Encoders:
[   10.957677] [drm]     TV1: INTERNAL_DAC2
[   11.057466] [drm] fb mappable at 0xD0040000
[   11.057473] [drm] vram apper at 0xD0000000
[   11.057476] [drm] size 3145728
[   11.057479] [drm] fb depth is 24
[   11.057482] [drm]    pitch is 4096
[   11.059653] fbcon: radeondrmfb (fb0) is primary device
[   11.080769] snd_intel8x0 0000:00:1e.2: intel8x0_measure_ac97_clock: measured 68087 usecs (3278 samples)
[   11.080773] snd_intel8x0 0000:00:1e.2: clocking to 48000
[   11.107621] Console: switching to colour frame buffer device 128x48
[   11.112719] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[   11.112723] radeon 0000:01:00.0: registered panic notifier
[   11.112955] [drm] Initialized radeon 2.39.0 20080528 for 0000:01:00.0 on minor 0
[   11.115385] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[   11.118754]  excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[   11.119484] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[   11.119849]  excluding 0x3f0-0x3ff 0x4d0-0x4d7
[   11.122150] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[   11.123437]  clean.
[   11.123462] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[   11.125485]  clean.
[   11.125514] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[   11.125522]  excluding 0xc0000-0xcffff 0xf0000-0xfffff
[   11.125555] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[   11.125575]  clean.
[   11.125593] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[   11.125598]  excluding 0x60000000-0x601fffff
[   11.125632] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[   11.126308]  clean.
[   11.175112] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
[   11.204108] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
[   11.204134] b43-phy0 warning: 5 GHz band is unsupported on this PHY
[   11.220411] Broadcom 43xx driver loaded [ Features: PMNLS ]
[   11.233884] systemd-journald[141]: Received request to flush runtime journal from PID 1
[   11.688092] b43 ssb0:0: firmware: direct-loading firmware b43/ucode5.fw
[   12.048570] input: DualPoint Stick as /devices/platform/i8042/serio1/input/input9
[   12.073745] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input7
[   12.108233] b43 ssb0:0: firmware: direct-loading firmware b43/pcm5.fw
[   12.164038] b43 ssb0:0: firmware: direct-loading firmware b43/b0g0initvals5.fw
[   12.175689] b43 ssb0:0: firmware: direct-loading firmware b43/b0g0bsinitvals5.fw
[   12.210731] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   12.519582] Adding 3143676k swap on /dev/sda5.  Priority:-1 extents:1 across:3143676k FS


* Используйте, пожалуйста, теги для оформления сообщений. Вывод вашей команды не полностью поместился в ваше сообщение, для полной передачи данных можете сохранить их в файл и загрузить на он-лайн сервис для хранения файлов, либо воспользоваться специальными ресурсами, такими как paste.debian.net. Leo.
« Последнее редактирование: 28 Июня 2015, 23:01:51 от Leo »
 

Оффлайн VKH

Re: Dell 610 wi fi
« Ответ #13 : 28 Июня 2015, 22:47:01 »
покажи вывод:
lspci -nn
 

Оффлайн mtc93rus

Re: Dell 610 wi fi
« Ответ #14 : 28 Июня 2015, 23:40:01 »
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port [8086:2591] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03)
00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 03)
00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 03)
00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 03)
00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 03)
00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d3)
00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 03)
00:1e.3 Modem [0703]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller [8086:266d] (rev 03)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 03)
00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 03)
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV370/M22 [Mobility Radeon X300] [1002:5460]
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express [14e4:1677] (rev 01)
03:01.0 CardBus bridge [0607]: Texas Instruments PCI6515 Cardbus Controller [104c:8036]
03:01.5 Communication controller [0780]: Texas Instruments PCI6515 SmartCard Controller [104c:8038]
03:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
 

Теги:
     

    [РЕШЕНО]Dell bistro 5459 не могу загрузить драйвер сетевой карты

    Автор Свотнев Сергей

    Ответов: 2
    Просмотров: 1368
    Последний ответ 15 Апреля 2017, 13:40:08
    от Свотнев Сергей
    Dell Poweredge 1850 установка Debian 7.8.0

    Автор bodyam

    Ответов: 3
    Просмотров: 2359
    Последний ответ 26 Февраля 2015, 11:10:16
    от ogost
    виснет на ноутбуке dell v 5459

    Автор vitalarg

    Ответов: 7
    Просмотров: 1988
    Последний ответ 09 Апреля 2017, 23:34:02
    от mrgoodvin